compustar for 2000 blazer
Printed From: the12volt.comForum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=66879
Printed Date: May 31, 2024 at 11:40 PM
Topic: compustar for 2000 blazer
Posted By: motherfudpucker
Subject: compustar for 2000 blazer
Date Posted: November 23, 2005 at 11:20 AM
Replies:
Posted By: thepencil
Date Posted: November 23, 2005 at 12:54 PM
Get plenty of liquid! Nothing will go smoothly the first time.
"I have looked in the downloads section and found several install sheets for compustar. my first question is - which brain module does this unit have?"
Why does it matter if you purchase the unit at a reputable shop? You should get what you pay for. Installaion and user guide are both in the box.
"second question - do I need a bypass module for my passlock 2 system?"
Yes, Passlock II
"Any other tips or tricks you may have for me..."
Again, get plenty of fluid, read, read, and read and read, then ask questions if you get stuck.
| ITEM | WIRE COLOR |POL| WIRE LOCATION |
| 12V|red |+ |ignition harness |
| STARTER|yellow |+ |ignition harness |
| IGNITION|pink |+ |ignition harness |
| SECOND IGNITION|white |+ |ignition harness |
| ACCESSORY|orange |+ |ignition harness |
| POWER LOCK|lt. blue |+ |brown plug at BCM *1 |
| POWER UNLOCK|white |+ |brown plug at BCM *1 |
| LOCK MOTOR|gray | |drivers kick panel |
| UNLOCK MOTOR|tan | |drivers kick panel |
| DISARM DEFEAT|tan | |passengers kick panel |
| PARKING LIGHTS +|brown | |lt. blue plug at BCM *1 |
| PARKING LIGHTS -|white *4 | |lt. blue plug at BCM *1 |
| HEADLIGHTS|PURPLE / white |- |purple plug at BCM *1 |
| DOOR TRIGGER|*2 |- |BCM *1 |
| DOME SUPERVISION|use door trigger | | |
| TRUNK/HATCH PIN|pink/black |- |lt. blue plug at BCM *1 |
|TRNK/HTCH RELEASE|black |- |purple plug at BCM *1 |
|FCTRY ALRM DISARM|lt.green |- |purple plug at BCM *1 |
| TACHOMETER|white | |PCM *3 |
| BRAKE WIRE|white |+ |steering column |
| HORN TRIGGER|black |- |steering column *5 |
Notes:
NOTE: This vehicle has the passlock II immobilizer system that, when adding a remote start, must be interfaced with. Use DEI part 555t or 555L. *1 The BCM is located to the right of the accelerator pedal below the radio. The plugs on the BCM face towards the drivers side. *2 Use tan for the drivers door located in pin B4 of the purple plug, orange for the passenger door located in pin B2 of the purple plug, and dk. blue/white for the rear doors and rear hatch located in pin B11 of the lt. blue plug, must diode isolate these wires. *3 The PCM is located on the passenger fender. On the 2.2L the wire is in a black 80 pin plug pin 10, and on the 4.3L the wire is in a red 32 pin plug pin 20. *4 This wire will not test when using the headlight switch. This wire is triggered by the DRL system. To meter the wire, start the car with the parking brake set, when the brake is released this wire will go to ground. *5 Also found in the brown plug at the BCM on vehicles with a factory alarm.
-------------
Be careful whose advice you buy, but be patient with those who supply it.
"I have looked in the downloads section and found several install sheets for compustar. my first question is - which brain module does this unit have?"
Why does it matter if you purchase the unit at a reputable shop? You should get what you pay for. Installaion and user guide are both in the box.
"second question - do I need a bypass module for my passlock 2 system?"
Yes, Passlock II
"Any other tips or tricks you may have for me..."
Again, get plenty of fluid, read, read, and read and read, then ask questions if you get stuck.
| ITEM | WIRE COLOR |POL| WIRE LOCATION |
| 12V|red |+ |ignition harness |
| STARTER|yellow |+ |ignition harness |
| IGNITION|pink |+ |ignition harness |
| SECOND IGNITION|white |+ |ignition harness |
| ACCESSORY|orange |+ |ignition harness |
| POWER LOCK|lt. blue |+ |brown plug at BCM *1 |
| POWER UNLOCK|white |+ |brown plug at BCM *1 |
| LOCK MOTOR|gray | |drivers kick panel |
| UNLOCK MOTOR|tan | |drivers kick panel |
| DISARM DEFEAT|tan | |passengers kick panel |
| PARKING LIGHTS +|brown | |lt. blue plug at BCM *1 |
| PARKING LIGHTS -|white *4 | |lt. blue plug at BCM *1 |
| HEADLIGHTS|PURPLE / white |- |purple plug at BCM *1 |
| DOOR TRIGGER|*2 |- |BCM *1 |
| DOME SUPERVISION|use door trigger | | |
| TRUNK/HATCH PIN|pink/black |- |lt. blue plug at BCM *1 |
|TRNK/HTCH RELEASE|black |- |purple plug at BCM *1 |
|FCTRY ALRM DISARM|lt.green |- |purple plug at BCM *1 |
| TACHOMETER|white | |PCM *3 |
| BRAKE WIRE|white |+ |steering column |
| HORN TRIGGER|black |- |steering column *5 |
Notes:
NOTE: This vehicle has the passlock II immobilizer system that, when adding a remote start, must be interfaced with. Use DEI part 555t or 555L. *1 The BCM is located to the right of the accelerator pedal below the radio. The plugs on the BCM face towards the drivers side. *2 Use tan for the drivers door located in pin B4 of the purple plug, orange for the passenger door located in pin B2 of the purple plug, and dk. blue/white for the rear doors and rear hatch located in pin B11 of the lt. blue plug, must diode isolate these wires. *3 The PCM is located on the passenger fender. On the 2.2L the wire is in a black 80 pin plug pin 10, and on the 4.3L the wire is in a red 32 pin plug pin 20. *4 This wire will not test when using the headlight switch. This wire is triggered by the DRL system. To meter the wire, start the car with the parking brake set, when the brake is released this wire will go to ground. *5 Also found in the brown plug at the BCM on vehicles with a factory alarm.
-------------
Be careful whose advice you buy, but be patient with those who supply it.
Posted By: autotech mobile
Date Posted: November 23, 2005 at 9:28 PM
Posted By: kgerry
Date Posted: November 24, 2005 at 7:24 PM
Posted By: OhioMike1101
Date Posted: November 24, 2005 at 8:28 PM