2000 yukon, remote start
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=67009
Printed Date: May 19, 2024 at 10:04 PM
Topic: 2000 yukon, remote start
Posted By: tintman97
Subject: 2000 yukon, remote start
Date Posted: November 25, 2005 at 7:10 PM
Installed a mars 22 RS all wires are correct. Used a Omega gm databus bypass and it programed but every time i start the truck by RS it shuts down in 3 sec. Security right well even with the key in the ignition it still shuts down after 3 sec. i tryed 2 bypasses and 2 RS units. Im stumped anyone got any ideas Snapper
Replies:
Posted By: murraymurray
Date Posted: November 25, 2005 at 8:14 PM
Check your tack setting and set it accordingly depwends where you got the signal from ------------- murraywatchel
Posted By: tintman97
Date Posted: November 25, 2005 at 9:48 PM
it was tachless voltage monitoring i used. i cant belive it makes that big of dif. the truck starts then dies 3 sec afterwards. Even with the key in the cylnder. snapper
Posted By: russ lund
Date Posted: November 26, 2005 at 4:00 PM
That is passlock II the key in the cylinder has no effect,only when the key is turned to the start position.Use a tach wire its way more reliable.
-------------
BigDog
Posted By: tintman97
Date Posted: November 26, 2005 at 6:42 PM
so does the key matter thar i programed from as the key i used was not orignal. Snapper
Posted By: murraymurray
Date Posted: November 26, 2005 at 7:01 PM
The key in the ignition in the run position but engine not running, Try and remote start it and it will more than likely start and stay running. Or else try start the car with the key and then hit start on the remote and then remove the keys and if engine stays running it is Passlock problem. Passlock ll does not have a chip in the key if the key turns in the tumbler it will work. Thankyou Murray ------------- murraywatchel
Posted By: mo12v
Date Posted: November 26, 2005 at 7:05 PM
What do you have the BLACK / Yellow wire hooked to from MARS 22??
Did you set the switch to Smart Start?
Did you adjust the Smart Adjustment to Blink while running?
Also be sure the TACH Adjustment is turned all the way down if using Smart Start
-------------
MO
Don't Learn from Others Mistakes
You Might Be the One That Knows.
Posted By: tintman97
Date Posted: November 26, 2005 at 7:45 PM
black and yellow on constant wire i was short of time. ill hook it to white on the coil but i think its a bypass issue not a tach prob myself. Omegas smart tach is pretty reliable. i had it on smart tach i tryed 2 units also . I fell retarded cause the bypasses are so easy to program. Snapper
Posted By: mo12v
Date Posted: November 26, 2005 at 8:20 PM
10 - 4............It does sound like a ByPass issue
Voltage Sense is reliable on most vehicles, but Tahoe, Yukon & Trailblazer have been a few of the GM Vehicles that I have found the TACH needs to be hook - up
-------------
MO
Don't Learn from Others Mistakes
You Might Be the One That Knows.
Posted By: tintman97
Date Posted: November 26, 2005 at 8:37 PM
k so that will work though turning the key to the on position and hiting the RS? dosent quite match what was said in the first place. Russland siad "That is passlock II the key in the cylinder has no effect,only when the key is turned to the start position" Snapper thanks for the help
Posted By: mo12v
Date Posted: November 26, 2005 at 8:43 PM
You probably are aware of this: https://www.wiringinstructions.com/238.htmYou could be facing both issues of ByPass & Tach........... I would want the ByPass hooked up & programmed, AFTER the TACH is learned ------------- MO
Don't Learn from Others Mistakes
You Might Be the One That Knows.
Posted By: tintman97
Date Posted: November 26, 2005 at 9:02 PM
dumb question how do u learn tach without the truck running? i thought it had to run to get it tuned in. Snapper
Posted By: mo12v
Date Posted: November 26, 2005 at 9:13 PM
YAH./.............. Start the Truck with Key...........Program TACH or SMART...then Program ByPass after you turn key off
-------------
MO
Don't Learn from Others Mistakes
You Might Be the One That Knows.
|