2006 Toyota Sienna Alarm/Remote Start Wiring

DIRECTWIRE™ WIRING INFORMATION - TOYOTA / SIENNA / 2006 / Remote Start
[PRINT THIS PAGE]

12volts  wht/red (30A), wht/blue (7.5A)  +  ignition harness Starter  BLACK / YELLOW  +  ignition harness Second Starter  N/A     Ignition  black  +  ignition harness Second Ignition  BLACK / YELLOW  +  ignition harness Third Ignition  N/A     Accessory  pink  +  ignition harness Second Accessory  N/A     Keysense  blue/black  -  ignition harness Notes: Using the status output to trigger this wire during remote start will disarm the factory alarm without unlocking the doors. Power Lock  lt. green  -  driver kick, 18 pin plug Notes: Meter these wires while turning the key in the driver door key cylinder. Power Unlock  blue (double pulse)  -  driver kick, 18 pin plug Notes: Meter these wires while turning the key in the driver door key cylinder. Can also use the passenger door key cylinder wire for unlock, which only requires a single pulse. It is blue / YELLOW (-) in the passenger kick in a 12 pin plug. Lock Motor  blue/red  5wi  driver kick, 12 pin plug Unlock Motor  WHITE/ red to red  5wi  driver kick, 18 pin plug Parking Lights+  do not use, relay rests at gnd     Parking Lights-  GREEN/ black  -  headlight switch Hazards  BLACK/ orange  -  hazard switch Turn Signal(L)  GREEN/ black  +  R side of fuse box, 30 pin plug Turn Signal(R)  GREEN/ YELLOW  +  R side of fuse box, 30 pin plug Reverse Light  RED / black  +  driver kick, harness to rear Door Trigger  blue  -  interior light switch on dash Notes: Can also use individual door trigger wires. The driver door is RED / yellow in the 16 pin plug, pin 14 at the BECU. The passenger door is RED / yellow in the 28 pin plug, pin 23 at the BECU. The left sliding door is gray, pin 19, in a 25 pin plug on the right side of the fuse box. The right sliding door is RED / white in the 16 pin plug, pin 16 at the BECU. The hatch door is GREEN / WHITE in the 28 pin plug, pin 25 at the BECU. Use all wires and diode isolate each. The BECU (Body ECU) is attached to the back of the fuse box under the driver side dash. Dome Supervision  RED / green  -  interior light switch on dash Trunk/Hatch Pin  common with door trigger wire     Hood Pin  RED / white  -  BECU, 10 pin plug, pin 10 Notes: The BECU (Body ECU) is attached to the back of the fuse box under the driver side dash. Trunk/Hatch Release  yellow/red (power back door)  -  bottom L of fuse box, 22 pin plug Notes: On vehicles without the power back door, the hatch release is GREEN/ black (-) at the BECU, 28 pin plug, pin 3. Meter this wire while open the hatch from the handle on the rear hatch. The hatch release motor wire is blue/black (+) at the BECU, 26 pin plug, pin 1. The BECU (Body ECU) is attached to the back of the fuse box under the driver side dash. Power Sliding Door  YELLOW /GREEN (L), purple (R)  -  bottom L of fuse box, 22 pin plug Factory Alarm Arm  arms with lock     Factory Alarm Disarm  disarms with unlock     Disarm No Unlock  use key sense wire     Tachometer  BLACK/ orange  ac  ECM, top plug, pin 5 Notes: The ECM (Engine Control Module) is behind the glove box. Wait to start  N/A     Brake Wire  GREEN / WHITE  +  brake pedal switch Parking Brake  RED / white  -  R side of fuse box, 36 pin plug Horn Trigger  GREEN/ black  -  horn switch Memory Seat 1  pink/blue  -  seat memory switch in door Memory Seat 2  lt. GREEN/ black  -  seat memory switch in door Memory Seat 3  N/A  -   Interface Module: Category: Immobilizer Bypass Required: Yes Type: Transponder Part #: 556UW Alternate Part1 #: DesignTech 20402 Alternate Part2 #: DesignTech 29402 Notes: Standard on LE, XLE and Limited models.

-------------
Mike M2
Tech Manager
CS Dealer Services

Thanks a lot ! Mike M2

need wiring diagram of 2004 mercedes benz for installing alarm.anyone can help ?thanks!

-------------
chan