2002 sebring, data bus
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=75026
Printed Date: May 10, 2024 at 1:10 PM
Topic: 2002 sebring, data bus
Posted By: nima
Subject: 2002 sebring, data bus
Date Posted: March 24, 2006 at 11:13 AM
I have 2002 sebring saden.i have compuster and CHRDAA bypass module install.i have problem with lock and unlock, its work but intermition lock and unlock.some time i have to press twice to unlock and lock.any help will be good
Replies:
Posted By: Geeque
Date Posted: March 24, 2006 at 11:34 AM
Tell me first how you tapped in for doorlocks.
-------------
Gary Kline
MECP Master Technician
Posted By: nima
Date Posted: March 24, 2006 at 1:11 PM
From remote start lock and unlock wire to CHRDAA module. from module to data bus
Posted By: xscash
Date Posted: March 24, 2006 at 1:23 PM
does the remotestart output both neg and pos to lock wires? try using a diode to stop the pos.
Posted By: nima
Date Posted: March 24, 2006 at 2:14 PM
what kind diod you want me to use 4001N? ,you want me to use on both lock and unlock side?
Posted By: nima
Date Posted: March 24, 2006 at 2:16 PM
yes its both(+ and-) ,can you give me diagram for diod like wich side gose where
Posted By: Velocity Motors
Date Posted: March 24, 2006 at 2:24 PM
The module is not working properly. I had problems with the all in one modules as well and I ended up using a polarity inverter with the resistors and it worked fine aferwards.
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: xscash
Date Posted: March 24, 2006 at 4:20 PM
toss a diode in line with each locking wire....silver line facing the remotstarter good luck, XS
Posted By: nima
Date Posted: March 25, 2006 at 3:54 AM
I try adding DIOD but it dose same thing. Velocity Motors, how can you add polarity inverter with the resistors. can you give me diagram and where can i get this polarity inverter with the resistors can you tell me detail........Thanks in advance
Posted By: Velocity Motors
Date Posted: March 25, 2006 at 8:10 AM
Diodes will not help at all. The Compustar systems use a (-) trigger only and without relays or a polarity inverter.Lock is positive thru a 1800 ohm resistor, unlock is positive thru a 750 ohm resistor. A polarity inverter is a small device that converters a (-) pulse to a (+) pulse ( just like having a relay just alot smaller and less wires) all you needt o do is wire in the proper resistor value inline of the output on the inverter. You can accomplish the same task with just two relays wired in like this.------------- Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: nima
Date Posted: March 25, 2006 at 8:23 AM
I have CHRDAA module do i have to connect the relay betwin remote start and module?
Posted By: Velocity Motors
Date Posted: March 25, 2006 at 8:39 AM
Don't use the CHRDAA module for door locks at all. Remove the door lock trigger wires from the Compsutar and attach the wires to the relays or inverter with the resistors inline. The CHRDAA will now only perform your bypass of the Sentry system and your trunk release. Did the Sebring come with a factory alarm system ??
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: nima
Date Posted: March 29, 2006 at 3:55 AM
Thanks Velocity Motors I removed from CHRDAA and add 2 relay its works fine
|