97 villager keyless entry

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=8401
Printed Date: October 31, 2024 at 6:04 PM

Topic: 97 villager keyless entry

Posted By: albl
Subject: 97 villager keyless entry
Date Posted: January 21, 2003 at 6:38 AM

i still need more help with door lock wireing.the wireing info that was posted for me stated that there is a single blue (-) wire that catches all doors i don't understand how to hook up a lock and unlock wire from my new remote combo start / keyless entry control unit.

can someone help me?????????

-------------
albl

Replies:

Posted By: Wolf-tech
Date Posted: January 21, 2003 at 8:55 AM

Can you be more specific with your problem, I am a slow typer.

Dave

Posted By: albl
Date Posted: January 21, 2003 at 9:49 AM

the wireing info says to use the blue wire there are two wires to conect to it the question is how do i conect two wires to one wire?

albl

-------------
albl

Posted By: Wolf-tech
Date Posted: January 21, 2003 at 10:53 AM

i think there should be a grn/wht and grn/ org wires for lock and unlock in that vehicle (drivers kick) neg.

97 villager right?

Dave

Posted By: albl
Date Posted: January 21, 2003 at 11:02 AM

not when it has a factory keyless entry those wires are used on non keyless entry models

-------------
albl

Posted By: albl
Date Posted: January 22, 2003 at 8:10 AM

can anyone tell me how to hook lock and unlock wires to the one blue wire (-) going to mod.

can any one help me?????????????

-------------
albl

Posted By: 10nesne1
Date Posted: January 22, 2003 at 11:45 AM

Wondering, does your vehicle comes with factory power door locks or not? Does your vehicle has OEM keyless entry or not? Do you have to install aftermaket door lock actuators?

97 villager comes with a negative trigger for door lock system. Your Remote Starter or Alarm system comes with two wires are Green and Blue colours. It should connect to the Villager without hooking up relays. If your vehicle required more than 200miliamps than you will need to hookup a couple relays to do the job.

3 Wire Positive Door Locks

This is one of the most common type of door lock switch configurations found in most vehicles. In most cases you will not need to add relays for this type. Most of the newer alarms and keyless entries on the market today have both positive and negative 200 ma door lock outputs that are usually capable of activating the factory relays. Should you need to add relays for a "3 wire negative" door lock system, just change both normally open terminals (87) from 12V(+) to ground. If your alarm or keyless entry has positive outputs only, you will have to connect the other side of the coils to ground and connect your outputs as shown. The lock and unlock wires below refer to the switch leads, not the motor legs.

Follow the digram above to change positive trigger to negative. All you need to do are ground both pin 87. It will change to negative trigger.

OR....

If you have to install aftermarket Door Lock Actuators than follow the diagram below.

Actuators / Reverse Polarity

This is practically identical to the 5 wire alternating 12V(+) system above. The only difference is there's no switch! Both motor legs rest at ground at the relays. To lock or unlock the vehicle, polarity is changed on one motor leg.

Good luck

Posted By: albl
Date Posted: January 22, 2003 at 1:04 PM

My car has factory keyless entry i'm trying to install a combo remote start / keyless entry all wireing info i've found calls for green / white wire(-) for lock and green / orange (-) for unlock my car doesn't have these wires the are for a non keyless entry car i'm trying to find out what color wires to look for on a keyless entry car (1997 merc villager)

thanks

-------------
albl

Posted By: 10nesne1
Date Posted: January 22, 2003 at 1:22 PM

Well, your vehicle has factory keyless entry. If you can't find those wire and you can take the driver's door panel apart and run the wires from the switch to the alarm, is it? (1997 merc villager)

Mercury

Villager

1996-1998

Alarm and Keyless Entry Wiring Colors and Notes
Function	Vehicle Color	Location
Constant +12 Volts:	WHITE/ PURPLE	IGNITION SWITCH HARNESS
Starter Kill:	RED & WHITE/ BLUE	IGNITION SWITCH HARNESS , *
Ignition +12 Volts:	BROWN	IGNITION SWITCH HARNESS
Dome Lights/Superv:	RED / BLACK (-)	IN 2-PIN CONNECTOR IN CENTER CONSOLE
OEM Horn:	BLACK (-)	STEERING COLUMN HARNESS
Power Lock:	GREEN / WHITE (-)	DRIVER'S KICK PANEL *****
Power Unlock:	GREEN/ ORANGE (-)	DRIVER'S KICK PANEL *****
Trunk Release:	N/A
Alarm Input Wire:	RED / BLACK (-)	IN 2-PIN CONNECTOR IN CENTER CONSOLE
Notes:

GREEN / WHITE and GREEN/ Orange are the door lock wire and you might have to look harder. Or go to the door lock switch. Good luck

Posted By: albl
Date Posted: January 22, 2003 at 1:59 PM

I've pulled door lock switch these are the the colors at the switch but the wires coming out of the door do not match i need to know what color wires to look for in the door harness .

thanks

-------------
albl

Posted By: 10nesne1
Date Posted: January 22, 2003 at 5:05 PM

Well, if you can't find those wires on the kick panel than did you try to find it from the door grommet. If you can those wire from the grommet than you can find it on the kick panel. If you can't find it from the door grommet than you will have to run the wire to the power door lock switch.

I checked three different wiring diagram and said those were the colours. It was located on the kick panel. Good luck