2004 accord, remote start
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=84833
Printed Date: June 08, 2024 at 4:32 PM
Topic: 2004 accord, remote start
Posted By: turbo5upra
Subject: 2004 accord, remote start
Date Posted: October 29, 2006 at 9:29 PM
hey has anyone ever had a issue with the 556u not working with a accord? It starts when i put the key in the igniton and push the remote or with the key near the lock..... relay in the box is working, i even built the cheater one with the key wrapped in wire and a relay but neither worked, anyone? thanx
Replies:
Posted By: Mike M2
Date Posted: October 30, 2006 at 6:23 AM
They work fine. Check to make sure the ring is closed tighter and closer to the edge of the switch. I actually unwrap the black plastic and twist the strands of wire so it will fit all the way against the outer edge. Also, Sounds crazy, but you wouldn't believe how many cars we get back with keys with erased codes. Pull the key out and make sure it starts the car.
-------------
Mike M2
Tech Manager
CS Dealer Services
Posted By: turbo5upra
Date Posted: October 30, 2006 at 6:31 AM
what do you mean by closed tighter? i've used both keys that he had, the gray one that we put in the box and the one with the factory controls on it.. they both start the car, and the remote starter works with either key near the ignition.... ive tried the ring in pretty much all postions....
Posted By: KPierson
Date Posted: October 30, 2006 at 6:31 AM
I have a 556U in my fiance's Accord with no problems at all. Make sure you use the valet key, otherwise it won't fit in the box! Those are some big keys.
-------------
Kevin Pierson
Posted By: Mike M2
Date Posted: October 30, 2006 at 6:44 AM
The ring must be closed smaller to fit tight around the switch. Use a wire tie or what i do is ducttape the ring into place VERY tight around the outer edge. The only other suggestion would be to try another ring. If even one of the strands get broken it's trash so it may be bad....
-------------
Mike M2
Tech Manager
CS Dealer Services
Posted By: turbo5upra
Date Posted: October 30, 2006 at 4:30 PM
is there any way to use the 556u with the factory ring? also do i need to attach the pink wire on it? i read someone was using it on a 00 accord
Posted By: davell
Date Posted: October 31, 2006 at 5:39 PM
I don't know if it's possible, but have you tried wrapping the antenna wire around the ignition cylinder two or three times? I had to do this with an Astrostart passkey module antenna to get a strong enough signal for key sense to work.
Posted By: turbo5upra
Date Posted: November 04, 2006 at 6:26 PM
hey guys.... got the car to start and run after making a transponder since my friend cut one strand in his 556u anywho.... the door locks and trunk are being a pita and since his multimeter was mia i wasent about to hunt for wires... i followed the door wires to the 2 lower green plugs above the fuses... the post that i got from here says YELLOW /GREEN for the trunk (don't quote me), and says its a positive trip... using his sytech pos lol.... which has a - trip for the trunk... so i wired up the rely to switch it and it works, tested that via test light connected it to that wire and nada.... sytechs and the color i got from here dont match.....does anyone have the colors they use themselves for this car? if not i'll go hunting with a multimeter later
|