528t pulse timer
Printed From: the12volt.com
Forum Name: Relays
Forum Discription: Relay Diagrams, SPDT Relays, SPST Relays, DPDT Relays, Latching Relays, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=127674
Printed Date: April 27, 2024 at 1:24 PM
Topic: 528t pulse timer
Posted By: emmuscat
Subject: 528t pulse timer
Date Posted: June 19, 2011 at 3:21 AM
Hello everyone , After several searches for help regarding 528T pulse timer conection i came across this forum and maybe someone can help me since i could not get any help in my country.
I want to connect a positive + signal to 528T PULSE TIMER to a buld so it will stay on for a few seconds .
Thanks
Emmanuel
Replies:
Posted By: howie ll
Date Posted: June 19, 2011 at 10:42 AM
Use the black white wire as before but cut the blue loop, as per the instructions.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: emmuscat
Date Posted: June 19, 2011 at 10:46 AM
Can you please give me all 6 wires conection
Thnaks
Posted By: howie ll
Date Posted: June 19, 2011 at 10:54 AM
Look in the downloads/manuals section on this site.
You should have looked before posting, it's your friend!
As are all of them, especially vehicle wiring.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: emmuscat
Date Posted: June 19, 2011 at 11:07 AM
I had the manual with the relay ,but could not figure it out
Thanks
Posted By: emmuscat
Date Posted: June 19, 2011 at 11:08 AM
emmuscat wrote:
I had the manual with the relay ,but could not figure it out how to conect it.
Thanks
Posted By: howie ll
Date Posted: June 19, 2011 at 11:44 AM
What are you trying to do?
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: emmuscat
Date Posted: June 19, 2011 at 11:49 AM
i am trying to connect the relay so when the buld is switched on it remain on for 20 seconds
Sorry about my english .
If it is posible tell me how to conect the 6 wireas of the 528T pulse timer
red 12volts to + to battery
black : - to battery
blue : cut
orange
brown
yellow
BLACK/ white
Thanks once agian
Posted By: emmuscat
Date Posted: June 19, 2011 at 11:53 AM
Sorry i forgot to tell you ,
So ineed to cut the + wire from the switch to the buld and include the relay in the middle
Thanks
Posted By: howie ll
Date Posted: June 19, 2011 at 12:22 PM
Orange not used.
Brown to red to 12 volt+, fuse at whatever you're powering up requires.
Yellow is output.
Adjust the screw potentiometer to give you the time, watch the internal relay, you won't need an initial test.
See this:-
528t.bmp------------- Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: emmuscat
Date Posted: June 19, 2011 at 1:11 PM
Thanks
Posted By: eric arevalo
Date Posted: February 01, 2016 at 4:52 PM
Hi,
I just did this this weekend. For positive pulse trigger you need to cut the blue wire. My 528t relay came by default with 27 seconds, maybe I'll go down to 20 secodns.
RED+YELLOW = +12V BATTERY(don't forget to put the right fuse here)
BLACK/ WHITE = INPUT WIRE.FOR +12V PULSE TRIGGER WIRE
BLACK = GROUND
BROWN = OUTPUT TO LIGHT
ORANGE = NOT USED.
OR - THE SAME AS ABOVE.
RED+BROWN = +12V BATTERY
BLACK = GROUND
BLACK/ WHITE = INPUT WIRE. FOR +12V PULSE TRIGGER WIRE
YELLOW = OUTPUT TO LIGHT
ORANGE = NO USED.
Good luck.
-------------
Thank you.
|
