Print Page | Close Window

2004 Jeep Liberty Alarm/Remote Start WIring

Printed From: the12volt.com
Forum Name: Vehicle Wiring Information & File Requests
Forum Discription: Request Car Alarm, Car Stereo, Cruise Control, Remote Starter, Navigation, Mobile Video, and Other Vehicle Specific Wiring Info, Manuals, Tech Tips
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=41446
Printed Date: April 20, 2024 at 3:34 AM


Topic: 2004 Jeep Liberty Alarm/Remote Start WIring

Posted By: swamprat323
Subject: 2004 Jeep Liberty Alarm/Remote Start WIring
Date Posted: October 22, 2004 at 5:25 PM

Need Alarm and RS info. Thanks



Replies:

Posted By: gpgtp00
Date Posted: November 21, 2004 at 1:47 PM
yeah me 2. =) I need the alarm wiring info. Thanks




Posted By: BNLUIS
Date Posted: November 21, 2004 at 1:56 PM

LIBERTY 2004
WIRE COLORSLOCATION
12 VOLTS CONSTANTRED & PINK/BLACKIGNITION SWITCH HARNESS
IGNITION 1RED / DARK BLUE (+)IGNITION SWITCH HARNESS
IGNITION 2BLACK/ ORANGE (+)IGNITION SWITCH HARNESS
ACCESSORY /HEATER BLOWER BLACK/ WHITE (+)IGNITION SWITCH HARNESS
STARTERYELLOW (+)IGNITION SWITCH HARNESS
PARKING LIGHTS (+)DO NOT USE !!@ BLACK Plug, Back of FUSE BOX in the top left corner
PARKING LIGHTS (-)LIGHT GREEN/ ORANGE (-) @ HEADLIGHT SWITCH or BCM, GREY 22 Pin Plug Pin 5 See NOTE *3 *SEE DIAGRAM*
DOOR TRIGGERSee NOTE *2@ BCM, See NOTE *3
DOME LIGHTTAN (-)@ BCM, See NOTE *3
POWER DOOR LOCKPINK/PURPLE @ REAR of FUSE BOX, TOP LEFT Plug Pin 14
POWER DOOR UNLOCK1-Wire System same wire*SEE DIAGRAM*
TRUNK RELEASEORANGE / PINK (-)@ BCM, GREY 26 Pin plug Pin 17 See NOTE *3
TACH SENSORany wire NOT GREEN/ ORANGE or ORANGE / GREEN at any IGNITION COIL or FUEL-INJECTOR
BRAKEWHITE/ TAN(+)@ SWITCH ABOVE BRAKE
HORNBLACK/ RED (-)@ STEERING COLUMN HARNESS
FACTORY DISARMLIGHT GREEN/ ORANGE (-) See NOTE *4@ BCM, Connector 2, Pin 9 *SEE DIAGRAM*

NOTE *1 the PARKING LIGHTS turn on with a (-) Negative thru a 1000 Ohm resistor See DIAGRAM

NOTE *2 the DRIVERS DOOR Trigger is a TAN (-) and the PASSENGER DOOR Trigger is a TAN/WHITE (-) when connecting to an Alarm System use both and Diode isolate.

NOTE *3 the BCM is attached to the LEFT of the FUSE BOX, Connector 1 is a GREY 26 Pin plug, and Connector 2 is a GREY 22 Pin plug.

NOTE *4 the Resistance value of this Resistor to Disarm can be a Standard 470 or 480 Ohm resistor.

posted_image

posted_image



-------------
Luis
Sound Waves
Is up to the installer to test all wires with a DMM whenever possible.




Posted By: Teamrf
Date Posted: November 21, 2004 at 4:29 PM
Also..all of the other doors are tan with a stripe as well. (Ex. Tan/Blk) You have to use ALL of them and diode isolate each one.

-------------
~The Rookie~
Rookie of the year that is...
Don't let the smoke out of your equiptment..it doesn't go back in.





Print Page | Close Window