the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2007 dodge sprinter, alarm, door locks


Post ReplyPost New Topic
< Prev Topic Next Topic >
moed 
Member - Posts: 3
Member spacespace
Joined: July 06, 2008
Location: New York, United States
Posted: July 06, 2008 at 4:18 PM / IP Logged  
I am trying to finish up an alarm install in a 2007 Dodge Sprinter but am having trouble getting the door locks to work. According to my tech sheet it should be the dark blue/black and dark blue/brown wires at the BCM. I have tried tying into these wires but no luck. The wiring is different than the 2006 and earlier.
howie ll 
Pot Metal - Posts: 16,466
Pot Metal spacespace
Joined: January 09, 2007
Location: United Kingdom
Posted: July 07, 2008 at 12:54 PM / IP Logged  
I think it's the same vehicle as the Mercedes Sprinter, if so its all CAN system and you will have to go to a company like Fortin to give you a conversion box so you may work the locks etc.
smcshark 
Member - Posts: 34
Member spacespace
Joined: June 22, 2008
Location: Ontario, Canada
Posted: July 07, 2008 at 3:06 PM / IP Logged  

I have DK Blue/ Red (reverse)

DK Blue/ Black (reverse) both in drivers door module

the ones you have are for side and rear doors, all are required to operate.

Automotive Electronic Specialist
moed 
Member - Posts: 3
Member spacespace
Joined: July 06, 2008
Location: New York, United States
Posted: July 07, 2008 at 9:52 PM / IP Logged  
smcshark How do I go about hooking up all 4 of the wires? Since it is rev I can't diode isolate. Please advise.
smcshark 
Member - Posts: 34
Member spacespace
Joined: June 22, 2008
Location: Ontario, Canada
Posted: July 07, 2008 at 10:52 PM / IP Logged  

you will have to take the outputs from the alarm system and do a type of hybrid lock system, a combination of revese polartiy set up and direct trigger to the sides and rear doors.

do you have the reverse polarity relay diagram? that is very important, have you done this before? if you have the relay set up for reverse then you simply hook up the outputs from the alarm to the trigger on the relays and to the sides and rears, you should use diode on the direct out puts just to be sure. email if you need diagrams, I have yet to figure out how to up load my tech data base to this forum. shark@efni.com

Automotive Electronic Specialist
moed 
Member - Posts: 3
Member spacespace
Joined: July 06, 2008
Location: New York, United States
Posted: July 10, 2008 at 8:58 PM / IP Logged  
Thanks, I will send you an email for the diagram.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Friday, March 29, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer