remote start triggering factory alarm

Home / the12volt's Install Bay / Car Security and Convenience / remote start triggering factory alarm (

Topic Closed)

Welcome Guest :)

Members

Search

Register

Login

< Prev Page < Prev Topic Next Topic >

solidgold007

Member - Posts: 5

Joined: January 11, 2009

Location: Wisconsin, United States

Posted: January 11, 2009 at 8:19 PM / IP Logged

The bypass module is the 791 from bulldog as well.

Anyone know why Bulldog doesnt say this is needed when installing the R/S?

I will try the above tomorrow. So the RED / YELLOW in the door is not needed then?

Thanks so much guys, makes alot more sense asking here than any of the shops I have tried to call.

Back to Top

loneranger

Copper - Posts: 572

Joined: December 28, 2008

Posted: January 11, 2009 at 8:43 PM / IP Logged

Mike M2 wrote:

DO NOT connect anything to the RED / yellow. Only the keysense is needed to disarm...

Great catch, Mike M2! I thought it was only key sense too but, went along with the poster. I should have trusted my manuals but, they were wrong about pulsing the key sense, as Chris Luongo pointed out.

Ideal - cmon dude, add to topics in a useful manner, not stuff that is obvious.

Story - Phzzzt! Hey, what happened?! ... Isn't it obvious?

Moral - Never dismiss the obvious.

Back to Top

solidgold007

Member - Posts: 5

Joined: January 11, 2009

Location: Wisconsin, United States

Posted: January 13, 2009 at 5:55 PM / IP Logged

OK I got the diodes and I am installing them tonight and rewiring the bypass like loneranger explained.

I am still confused on where the RED / Black FASD (-) when running on the R/S is supposed to go. Any ideas? I get the keysense thing. I drew a diagram to help me out. Thanks for the help guys.

Back to Top

jar754

Copper - Posts: 142

Joined: December 16, 2003

Location: Illinois, United States

Posted: January 13, 2009 at 8:53 PM / IP Logged

nothing gets connected to the rs fasd as mike has stated earlier.the keysense is acting as the fasd

Back to Top

loneranger

Copper - Posts: 572

Joined: December 28, 2008

Posted: January 13, 2009 at 10:59 PM / IP Logged

solidgold007 wrote:

OK I got the diodes and I am installing them tonight and rewiring the bypass like loneranger explained.

I am still confused on where the RED / Black FASD (-) when running on the R/S is supposed to go. Any ideas? I get the keysense thing. I drew a diagram to help me out. Thanks for the help guys.

Don't connect the R/S's RED / BLACK(FASD) wire to anything. The R/S's WHITE(- IGNITION: thin wire) output will trigger the bypass, by holding the GWR. It will also dis-arm the factory security system, by holding the key-sense, if you wired the diode properly.

Ideal - cmon dude, add to topics in a useful manner, not stuff that is obvious.

Story - Phzzzt! Hey, what happened?! ... Isn't it obvious?

Moral - Never dismiss the obvious.

Back to Top

< Prev Page

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

remote start triggering factory alarm

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.