the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

amp


Post ReplyPost New Topic
< Prev Topic Next Topic >
93_civic 
Member - Posts: 41
Member spacespace
Joined: February 20, 2009
Location: Washington, United States
Posted: September 06, 2009 at 5:11 AM / IP Logged  

whats the diffrence between a Class A/B Operation amp, and a Class D Operation amp?

also, if the amp says 1 ohm stable, does that mean i will get the best performance out of my sub if i run it on 1 ohm?

thanks in advance! amp - Last Post -- posted image.

yimke 
Copper - Posts: 417
Copper spacespace
Joined: June 23, 2009
Location: Nebraska, United States
Posted: September 06, 2009 at 9:28 AM / IP Logged  
Class A/B is a hybrid between A and B. I would recommend these for running 4 channels. The efficiency on these are around 60-70% depending on the design. Class A amplifiers are on 100% of the time and are known for their great "no distortion" characteristics. Class B on the other hand are switched on/off so they are on only 50% of the time. They suffer mass "crossover distortion" so I would NEVER use this for pushing speakers, only subs. But luckily today most of the amps out there are the hybrid between the two and much better design/efficiency.
Class D amplifiers are typically called switching amplifiers. The signal or Sine wave is broken down into individual segments switching on/off. And the actually output it slightly after the input sine wave. This usually causes distortion at the higher frequencies, so a LP filter is recommended on them and these are meant for subs. The greatest benefit of this is efficiency though. Class D amps are around 90% or above efficiency now.
Just because an amp says it is 1 ohm stable doesn't mean that you absolutely have to run it at 1 ohm. The downside to running it this low of impedance is the amp runs HOT. This can lead to less efficiency and possible overheating damage to the circuits of the amp. If you ran it at 2 ohms on the same amp theoretically you would only lose 3db. Most people cant notice the difference, and your amp will be happier in the long run.
DYohn 
Moderator - Posts: 10,741
Moderator spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Mobile Audio and Video. Click here for more info.spacespace
Joined: April 22, 2003
Location: Arizona, United States
Posted: September 06, 2009 at 9:29 AM / IP Logged  
Amplifier class describes how it is designed electronically.  A/B is generally the best sounding and D is the highest efficiency.  1-ohm stable means the amplifier will handle any speaker load down to 1-ohm.  Amplifiers tend to sound best and function the best with higher loads.
Support the12volt.com
DYohn 
Moderator - Posts: 10,741
Moderator spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Mobile Audio and Video. Click here for more info.spacespace
Joined: April 22, 2003
Location: Arizona, United States
Posted: September 06, 2009 at 9:33 AM / IP Logged  

yimke wrote:
Class A/B is a hybrid between A and B. I would recommend these for running 4 channels. The efficiency on these are around 60-70% depending on the design. Class A amplifiers are on 100% of the time and are known for their great "no distortion" characteristics. Class B on the other hand are switched on/off so they are on only 50% of the time. They suffer mass "crossover distortion" so I would NEVER use this for pushing speakers, only subs. But luckily today most of the amps out there are the hybrid between the two and much better design/efficiency.
Class D amplifiers are typically called switching amplifiers. The signal or Sine wave is broken down into individual segments switching on/off. And the actually output it slightly after the input sine wave. This usually causes distortion at the higher frequencies, so a LP filter is recommended on them and these are meant for subs. The greatest benefit of this is efficiency though. Class D amps are around 90% or above efficiency now.
Just because an amp says it is 1 ohm stable doesn't mean that you absolutely have to run it at 1 ohm. The downside to running it this low of impedance is the amp runs HOT. This can lead to less efficiency and possible overheating damage to the circuits of the amp. If you ran it at 2 ohms on the same amp theoretically you would only lose 3db. Most people cant notice the difference, and your amp will be happier in the long run.

1) There are no "Class B" amplifiers available today.

2) the high-pass filter in a Class D amplifier is to remove the noise from the switching frequency of the output device and is generally not in the audible band.  There are plenty of great sounding full-range class D amplifiers: they are NOT just "meant for subs."

Support the12volt.com
93_civic 
Member - Posts: 41
Member spacespace
Joined: February 20, 2009
Location: Washington, United States
Posted: September 06, 2009 at 5:33 PM / IP Logged  

ok thanks for the help guys!

im planning on running a 600 watt RMS Performance Technique 12" DVC Sub at 2ohms,

can anyone tell me if this amp would sound good with it?

    • Amplifier Class : Class A/B
    • Number of Channels : 1-Channel
    • Maximum Power : 1100 Watts
    • RMS Power Output @ 4 Ohms : 250 Watts x 1-Channel
    • MAX Power Output @ 2 Ohms : 1100 Watts x 1-Channel
    • Bridged Power : N/A
    • THD : 0.01%
    • Signal-to-Noise Ratio (dB) : 103dB
    • Frequency Response (Hz) : 9Hz~50kHz
    • Built-in Crossover : Yes
    • High-Pass Crossover Frequency : Fixed, 200Hz
    • Low-Pass Crossover Frequency : 35Hz~160Hz
    • Bass Boost : 0dB~+18dB
    • Bass Remote : Yes
    • Fan Cooled : N/A
    • Fuse Rating : 25A x 1

-Thanks again for all your help!!!  amp - Last Post -- posted image.

i am an idiot 
Platinum - Posts: 13,666
Platinum spaceThis member consistently provides reliable informationspace
Joined: September 21, 2006
Location: Louisiana, United States
Posted: September 06, 2009 at 5:56 PM / IP Logged  

Can't tell you how it is going to sound, but if you look closely at the power ratings, notice that they give you the RMS into 4 ohms and they give you max into 2 ohms.

So as long as you know you are going to be sending no more than 500 watts to your speaker, and that is enough power for you, then so be it.

DYohn 
Moderator - Posts: 10,741
Moderator spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Mobile Audio and Video. Click here for more info.spacespace
Joined: April 22, 2003
Location: Arizona, United States
Posted: September 06, 2009 at 6:49 PM / IP Logged  
93_civic wrote:

Fuse Rating : 25A x 1

25A @ 14.4 volts, with 65% Class A/B efficiency means this amp will produce approximately 234 watts.  Must be a marginal brand to publish the bogus specs you list.

Support the12volt.com
93_civic 
Member - Posts: 41
Member spacespace
Joined: February 20, 2009
Location: Washington, United States
Posted: September 06, 2009 at 11:05 PM / IP Logged  

my bad! hey DYohn, can u tell me what approximate wattage this amp will get?

thanks again!

Model: MA Audio HK-601

Hard Kore Series 1200 Watt 1 Channel High Performance Mono Block Car Amplifier

1200 Watts Rated Output Power

1 x 600W RMS @ 2 Ohm Mono

1 x 500W RMS @ 4 Ohm Mono

Fully Unregulated MOSFET Power Supply

2 Ohm Stable @ Mono

Temperature, Voltage, and Output Level LCD Display

Thermal, Short, and Overload Protection Circuitry

Power/Protection LED Indicators

Stainless Steel Finish Heat Sink

Double Sided Black Epoxy PCB Board

Quiet Internal Fan Cooling System

Gold Plated RCA Jacks

Gold Plated Block Terminals

Low Level RCA Inputs

Specifications:

Variable Subsonic Filter: 20Hz-50Hz

Variable Bass Boost: 0-18dB

Adjustable Input Sensitivity

Frequency Response: 20Hz-20 kHz

THD: <0.05% @ 4 Ohm

THD: <0.1% @ 2 Ohm

Channel Separation: 60dB

S/N Ratio: >90dB

Dimensions (L x W x H) 11.81" x 12.4" x 2.7"

(3) 30A Fuses


Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, March 28, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer