the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

mazda 3 12v constant


Post ReplyPost New Topic
< Prev Topic Next Topic >
rjkboyle 
Copper - Posts: 97
Copper spacespace
Joined: August 18, 2010
Location: British Columbia, Canada
Posted: September 29, 2012 at 3:52 PM / IP Logged  
Hey guys just about to start the install on a 2007 Mazda 3, but curious to know what power wires to use. I know at the ignition there is a red and BLACK/ red wire both fused at 30amp. My 5701 has 3 constant wires fused at 30, the main 15amp power wire, then a 5amp wire for a relay.
On previous Toyotas I've worked on there was a thick white wire providing power to the inside fuse box that I used, but can't find anything like that here.
Is it okay to use the two power wires at the ignition, I don't want to over load anything.
Thanks for your help!!!!!
rjkboyle 
Copper - Posts: 97
Copper spacespace
Joined: August 18, 2010
Location: British Columbia, Canada
Posted: September 29, 2012 at 6:25 PM / IP Logged  
Anyone? If you don't know where to get a bigger power wire what are your thoughts on using the ones at the ignition? I read a installation guide where a guy used the ignition wires but just hooked two 30amp wires up to a 30amp ignition wire.
Thoughts?
rjkboyle 
Copper - Posts: 97
Copper spacespace
Joined: August 18, 2010
Location: British Columbia, Canada
Posted: September 29, 2012 at 7:59 PM / IP Logged  
Okay new question hopefully someone can shine some lights on. Since mazda has the worse door triggers ever, I'm hoping to just use the dome light wire, I tested that it will work fine. But when the car shuts off, the dome light comes on.
So if I remote start, then shut off the remote starter, or it times out, will the dome light come on setting off the alarm??
dasbogie 
Silver - Posts: 514
Silver spacespace
Joined: September 30, 2006
Location: Pennsylvania, United States
Posted: September 29, 2012 at 9:05 PM / IP Logged  
The 5701 can be programmed for open door triggers
Advanced
rjkboyle 
Copper - Posts: 97
Copper spacespace
Joined: August 18, 2010
Location: British Columbia, Canada
Posted: September 29, 2012 at 10:58 PM / IP Logged  
Can you elaborate, and maybe explain what I need to do please and thanks.
JWorm 
Platinum - Posts: 2,208
Platinum spacespace
Joined: December 11, 2002
Location: New Hampshire, United States
Posted: September 30, 2012 at 10:35 AM / IP Logged  
Divide up the power wires going to the two circuits in the ignition harness. I would do the red 30, red 15, and 5 amp to one circuit, and the RED / white and RED / black to another.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, March 28, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer