the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

nissan 300zx remote starter


Post ReplyPost New Topic
< Prev Topic Next Topic >
scauntay 
Member - Posts: 16
Member spacespace
Joined: January 09, 2004
Location: United States
Posted: January 09, 2004 at 8:20 PM / IP Logged  

i have a remote starter kit for my Z but im not sure about the wiring. i can do it, seems easy, but i need a detailed wiring diagram for my 1991 300zx non turbo. if anyone can help me out that would be great. thanks

S

Bnluis 
Silver - Posts: 578
Silver spacespace
Joined: December 24, 2002
Location: New York, United States
Posted: January 09, 2004 at 8:35 PM / IP Logged  
NISSAN 300ZX 1990-91
WIRE COLORSLOCATION
12 VOLTS CONSTANTBLK/WHT IGN HARNESS
IGNITION 1BLK/RED       IGN HARNESS
ACCESSORY /HEATER BLOWER 1BLUIGN HARNESS
STARTERBLK/WHT AND BLK/YELIGN HARNESS
PARKING LIGHTSGRN/REDAT LIGHT SWITCH
DOMELIGHTRED / WHTAT ANTI-THEFT MOD "BEHIND GLOVE BOX"
PWR DOOR LOCKADD ACTURATORDRV DOOR
PWR DOOR UNLOCKADD ACTUATORDRV DOOR *SEE DIAGRAM*
TACH SENSORYEL/REDAT ECM

BRAKE

RED / BLKAT SWITCH ABOVE BRAKE PEDAL

HORN

  GRN/WHT (-)STEER COLM

FACTORY DISARM

  GRY/REDDRV KICK PANEL
Luis
Sound Waves
Is up to the installer to test all wires with a DMM whenever possible.
scauntay 
Member - Posts: 16
Member spacespace
Joined: January 09, 2004
Location: United States
Posted: January 10, 2004 at 2:58 PM / IP Logged  
thanks bnluis, would happen to know where i can get a detailed illustration of all that stuff?
dyer 
Copper - Posts: 206
Copper spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: May 24, 2002
Location: United States
Posted: January 10, 2004 at 4:24 PM / IP Logged  
all your ignition wires will be run together in the ignition harness (under steering column, and most of the others will be in a kick panel. Once you start looking, you will find them quickly. good luck
Dyer
scauntay 
Member - Posts: 16
Member spacespace
Joined: January 09, 2004
Location: United States
Posted: February 05, 2004 at 2:03 AM / IP Logged  
i know this post has been dead for a while but i just found time to get to doing this. i have an ass load of wires that i have no clue where they go. here is the list if anyone could help out. i know some of them dont apply to my car but here is what is onthe starter kit i got....ground-ground for temp sensor
manual start input(-)-temp sensor
+12v dc-1a max power for door lock module
door unlock output(-)-250mA (-) output:factory door           
     lock
+ trigger(+)-door pin switch
glow plug input(-)-GP wire: changes (+) to (-)
factory disarm output(-)-250mA (-) output
hood input(-)-hood pin switch
interior light output(-)-250mA (-) output
brake switch input(+)-brake wire changes (-)to(+)
tach or oil sensor input-vehicle tach or oil sensor
      wire
starter interrupt output(-)- 250mA (-) output
-trigger input(-)- door pin switch
ground out when run(-)- 250mA (-) output
horn output(-)- 250mA (-) output
parking light output(+)- 10A (+)relay output
trunk release output(+)-10A (+)relay output
parking light output(+)-10A (+)relay output
30A fuse- +12VDC input
ignition 1 output(+)-ignition 1
ground input
start output(+)-start
acc output(+)- acc
30A fuse- +12VDC input
Teamrf 
Gold - Posts: 1,031
Gold spacespace
Joined: January 13, 2004
Location: United States
Posted: February 05, 2004 at 1:23 PM / IP Logged  
door unlock output(-)-250mA (-) output:factory door           
     lock
+ trigger(+)-door pin switch
hood input(-)-hood pin switch
interior light output(-)-250mA (-) output
brake switch input(+)-brake wire changes (-)to(+)
tach or oil sensor input-vehicle tach or oil sensor
      wire
starter interrupt output(-)- 250mA (-) output
-trigger input(-)- door pin switch
ground out when run(-)- 250mA (-) output
horn output(-)- 250mA (-) output
parking light output(+)- 10A (+)relay output
trunk release output(+)-10A (+)relay output
parking light output(+)-10A (+)relay output
30A fuse- +12VDC input
ignition 1 output(+)-ignition 1
ground input
start output(+)-start
acc output(+)- acc
30A fuse- +12VDC input
~The Rookie~
Rookie of the year that is...
Don't let the smoke out of your equiptment..it doesn't go back in.
Teamrf 
Gold - Posts: 1,031
Gold spacespace
Joined: January 13, 2004
Location: United States
Posted: February 05, 2004 at 1:24 PM / IP Logged  
Those are the wires you will need. Not all of them will be needed..if you don't want trunk pop or it is operated by a metal latch then you will need more equiptment for it.
~The Rookie~
Rookie of the year that is...
Don't let the smoke out of your equiptment..it doesn't go back in.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Friday, March 29, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer