2005 Chrysler 300, remote start/airbag light

Home / the12volt's Install Bay / Car Security and Convenience / 2005 Chrysler 300, remote start/airbag light (

Topic Closed)

Welcome Guest :)

Members

Search

Register

Login

< Prev Topic Next Topic >

Big Dog

Gold - Posts: 1,265

This member consistently provides reliable information

Joined: May 02, 2002

Location: Quebec, Canada

Posted: September 15, 2004 at 11:36 AM / IP Logged

Has anybody had AIBAG light come on after doing r-start and WireMagic's method of doing 2nd ign and crank?

Back to Top

larkster

Copper - Posts: 98

Joined: October 04, 2003

Location: Canada

Posted: September 15, 2004 at 12:30 PM / IP Logged

only done one. the ignition circuit is the same as the caravan. second starter wire PURPLE / brown negative with 180ohm resistor. not sure what wiremagic says but i dont remember there being a second ignition wire.

Back to Top

jcap

Member - Posts: 41

Joined: May 14, 2004

Location: Canada

Posted: September 15, 2004 at 11:59 PM / IP Logged

if you hooked up the wiring bypass as per wire magic method . the cruise control will not wokring also.

jcap

Back to Top

another-kelly

Silver - Posts: 618

Joined: July 11, 2004

Location: United States

Posted: September 16, 2004 at 12:16 AM / IP Logged

here's DEI's:

12volts	lt. blue/red (15A)	+	ignition harness
Starter	pink/dk. green	+	ignition harness
Second Starter	PURPLE / brown	-	ignition harness
Ignition	pink/white	+	ignition harness
Second Ignition
Third Ignition
Accessory	PURPLE / brown	-	ignition harness

CHRYSLER, 300, 2005, Second Starter

The second starter wire is negative trigger thru an 180 ohm resistor. MUST use a relay. Refer to DirectFax document 1083 for wiring information.

http://www.directechs.com/techtips/pdfs/resources/security/directed_techtips/1083.pdf

Back to Top

larkster

Copper - Posts: 98

Joined: October 04, 2003

Location: Canada

Posted: September 16, 2004 at 8:14 PM / IP Logged

did one today again...cut PURPLE / brown wire measured it. this wire does keysense 8.4k starter 180ohm and accessory 620ohm. i hooked up the second starter and the acc and everything works fine. no airbag light on and test drove cruise works fine...however i did have the check engine light come on...anybody else

Back to Top

extreme1

Silver - Posts: 1,070

Joined: February 12, 2003

Location: Canada

Posted: September 16, 2004 at 11:40 PM / IP Logged

I use a DEI 456L resistance learning module for 2nd ign/start.

Shaughn Murley

Install Manager, Dealer Services

Visions Electronics

Red Deer, Alberta

Back to Top

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

2005 Chrysler 300, remote start/airbag light

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.