the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

4 ch amp, 2 component 2 ohm, 1 sw 4 ohm


Post ReplyPost New Topic
< Prev Topic Next Topic >
mrep 
Member - Posts: 3
Member spacespace
Joined: October 27, 2007
Location: Pennsylvania, United States
Posted: October 27, 2007 at 10:27 PM / IP Logged  

I just bought a pair of components and a sub from a friend.  He threw in a 4 channel amp as well.  I'm not really looking for perfection, but wanted to upgrade the sound a bit.  I'm just unsure about the amp hookup.  I've installed a few systems with all speakers having the same impedance.  This system will have two component sets (rated at 2 ohms a piece - (the 6.5 woofer reads 2.8ohm and the tweeter reads 3.2 )) and one 10 " sw unless I can hook something else to the fourth channel.

I assume each comp set will run at two ohms on the front two channels of the amp.  I wanted to add the woofer on the rear side, but it runs at 4 ohms. 

I'm worried too much about the actual install, but wondered if this hookup will this create any problems with the amplifier.

Also, when installing the crossovers; should I install them before the amp, or after the signal comes out?  Unfortunately, they aren't RCA-wired, they have screw terminals, but I can work with that. 

M. Reppert
extacy 
Member - Posts: 46
Member spacespace
Joined: July 05, 2007
Location: Pakistan
Posted: October 28, 2007 at 4:07 AM / IP Logged  

Can you please specify which amplifier, which subwoofer and which components are you talking about ?

Usually in this kind of a setup, Front channels take the components (you need to be sure your amp is 2ohm stable stereo) and the rear 2 channels are bridged and wired up to the subwoofer.

Thats how im running my setup too.

mrep 
Member - Posts: 3
Member spacespace
Joined: October 27, 2007
Location: Pennsylvania, United States
Posted: October 28, 2007 at 6:34 AM / IP Logged  

It's a boss rev-1000 ( says 200 rms per channel/400 max).  I don't believe the numbers, but I shouldn't need too much to push the speakers.

The front channels will take care of the components.  The rear will handle the sw.  I was also wondering about a 3rd speaker, say a 6x9 to fill from the rear.  This would ruin the bridging though unless I use another crossover.

The components are are a pair of 6.5" infinity reference 6020cs (2 crossovers included).  They handle 90 rms @ 2 ohms.   The sub is an mtx 10" @ 200 rms ( I think 4 ohm).

If I bridge the amp for the sub, will that be running down to two ohms?  I assume that would solve it.

If you know anything about the crossovers, let me know.  I've seen many diagrams show the crossover before the amplifier, which would mean the amp wouldn't waste power amplifying power that was shielded out anyway, but I'd need to use all four channels just for the speakers.  Two for the woofers and two for the tweeters.  Then the input would come in already filtered, but I may lose the sub.  Know anything about the power ratings of the crossover?  I doubt I'm going to blow too much with this system, but I'd hate to ruin the crossovers with an incorrect install.

M. Reppert
mrep 
Member - Posts: 3
Member spacespace
Joined: October 27, 2007
Location: Pennsylvania, United States
Posted: October 28, 2007 at 5:23 PM / IP Logged  

Oh, to clear up the amp installation:

The sub is 4ohm by the way....

I would hook the components into the front (needing 90 rms) and bridge the woofer (if that would work), which needs 200rms.  Would bridging it give the woofer  2 times the power the components get?  This seems like it would work perfectly as I turn up the volume.....

I know that may be a very simplistic interpretation...those usually tend to be wrong.

Any thoughts????

M. Reppert
haemphyst 
Platinum - Posts: 5,052
Platinum spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Mobile Audio and Video. Click here for more info.spacespace
Joined: January 19, 2003
Location: Michigan, Bouvet Island
Posted: October 28, 2007 at 6:00 PM / IP Logged  
1: You have passive crossovers, they will be between the amplifier and the drivers.
2: Bridge the rear channels of the amplifier to the woofer.
Don't make it more difficult on yourself than you have to. If the amp will be able to handle the 2 ohm load of the Infinities, then it will handle the bridged load of a 4 ohm subwoofer, as well.
3: DON'T try to run the woofer off one rear channel and a six-by off the other rear channel... It'll only sound like arse.
It all reminds me of something that Molière once said to Guy de Maupassant at a café in Vienna: "That's nice. You should write it down."

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Wednesday, October 27, 2021 • Copyright © 1999-2021 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer