the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

The New Guy's quick questions.


Post ReplyPost New Topic
< Prev Topic Next Topic >
95oakmax 
Member - Posts: 3
Member spacespace
Joined: June 29, 2005
Location: United States
Posted: June 29, 2005 at 9:44 PM / IP Logged  
Hello, I'm new to serious car audio and I am also new to these forums. Over the weekend I will be installing a SoundSplinter RL-i 10" subwoofer and two MTX amplifiers to my aftermarket system.
I believe I have purchased everything for this set-up. I am nearing completion with my box, I have purchased 3 16' Lightning Audio BOLT RCAs, I have a few four-packs of ring terminals, in-line fuse block/fuse, a distribution block for the trunk, and even a decent amount of 16 gauge speaker wire.
One thing I am not sure about - my power/ground wire. I purchased 21 feet of no.4 THHN wire for this and just wanted to make sure this would be good enough wire for my application. (I have ~400 watts going to the sub and ~200 to the internal speakers)
Sorry to bother you all with this most-likely tired and frustrating wiring question - but as you might have guessed, I just am not sure of the answer.
-Jonathan
1995 Maxima GLE-JVC AR-5000 HU-Polk dB6750 Comps-Polk dB675 Coax-SoundSplinter RL-i 10"-Powered by MTX
dwarren 
Platinum - Nominee - Posts: 1,811
Platinum - Nominee spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: December 03, 2004
Location: California, United States
Posted: June 29, 2005 at 9:59 PM / IP Logged  
Check out the Power and Ground Calculator to the left. Then feel guilty for asking questions like this. The New Guy's quick questions. -- posted image.
95oakmax 
Member - Posts: 3
Member spacespace
Joined: June 29, 2005
Location: United States
Posted: June 29, 2005 at 10:15 PM / IP Logged  
Sorry, perhaps I need to redirect my question slightly. I did not mean to ask whether or not 4 gauge wire would be sufficient, but rather I am asking about the type of wire. As I understand it, Monster-Cable type wiring has as many as 1800 strands of wire within a 4 gauge wire, whereas the THHN that I purchased only has around 16-18 strands.
As I have been taught the electrons flow only on the surface of the wire, and therefore more strands=more surface area=better transfer of electrons. However, others have also told me that the only difference the strand count makes is to the flexibility of the wire.
That was the nature of my question - "Is THHN good enough? or Should I eventually upgrade to Welding wire or Monster Cable (higher strand count)?"
I did take a look at that spreadsheet for Power/Ground wiring, thanks for pointing it out, it is quite useful.
-Jonathan
1995 Maxima GLE-JVC AR-5000 HU-Polk dB6750 Comps-Polk dB675 Coax-SoundSplinter RL-i 10"-Powered by MTX
forbidden 
Platinum - Posts: 5,352
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Mobile Audio and Video. Click here for more info.spacespace
Joined: November 01, 2003
Location: Alberta, Canada
Posted: June 30, 2005 at 7:28 PM / IP Logged  

The other thing to consider other than flexibility is this. The more strands, the higher the amount of surface area, next how's about the cables ability to take heat, moisture, cold etc. that an engine bay has? I would go to a good 4 gauge car audio cable if I was in your shoes.

Top Secret, I can tell you but then my wife will kill me.
Mad Scientists 
Silver - Posts: 380
Silver spacespace
Joined: February 07, 2004
Location: United States
Posted: July 04, 2005 at 12:27 PM / IP Logged  

95oakmax wrote:
As I have been taught the electrons flow only on the surface of the wire, and therefore more strands=more surface area=better transfer of electrons. However, others have also told me that the only difference the strand count makes is to the flexibility of the wire.

AC flows on the surface of the wire, DC flows through the wire..

Jim

boulderguy 
Silver - Posts: 510
Silver spacespace
Joined: April 17, 2005
Location: United States
Posted: July 04, 2005 at 8:41 PM / IP Logged  
Mad Scientists wrote:

AC flows on the surface of the wire, DC flows through the wire..

Jim

No kidding?  Ironic that home wiring is mostly solid while car is multi-strand.  I'm sure this is primarily about flexibility tho.  Any input about fewer strands vs many-strands?  Mayeb there's a good post about this?  Mostly interested for theoretical reasons.

wirewise 
Moderator - Posts: 489
Moderator spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member consistently provides reliable informationspace
Joined: March 07, 2002
Location: California, United States
Posted: July 04, 2005 at 8:56 PM / IP Logged  
Mad Scientists wrote:
AC flows on the surface of the wire, DC flows through the wire..
I was taught that electricity (AC and DC) flows on the surface of the conductor (wire). Do you have any reference to this?
~wirewise~
Mad Scientists 
Silver - Posts: 380
Silver spacespace
Joined: February 07, 2004
Location: United States
Posted: July 05, 2005 at 5:19 AM / IP Logged  

(First attempt to post seems to have locked up.. second attempt here.)

certainly..

"As previously mentioned, the skin effect is where alternating current tends to avoid travel through the center of a solid conductor, limiting itself to conduction near the surface. This effectively limits the cross-sectional conductor area available to carry alternating electron flow, increasing the resistance of that conductor above what it would normally be for direct current: "

http://www.allaboutcircuits.com/vol_2/chpt_3/6.html

"When wire (specifically, solid copper conductors as are used for transformers) is used to carry DC current, the entire cross sectional area of copper carries the current equally. When wire is used for AC current, the current is carried differently. At low frequencies, the current flow is not significantly affected by the skin effect. As you get into the higher frequencies (as those used to drive a transformer in a switch mode power supply), the current flow is carried disproportionately by the outer area of the copper wire (especially for large single solid conductors). This is called the skin effect."

http://www.bcae1.com/trnsfrmr.htm

And I learned about this effect during Non Destructive Testing with Magnaflux machines..

"this type of current is passing through zero 120 times per second, the magnetic field it generates is not able to penetrate very far beneath the surface of the part. The current and the field generated stay near the skin of the part, no matter how high the value of current used. This is called "skin effect". AC works very well for locating defects open to the surface."

http://www.magnaflux.com/files/library/Technical_Papers//Types%20of%20Magnetizing%20Current.pdf

Jim

thepencil 
Gold - Posts: 1,526
Gold spacespace
Joined: December 16, 2002
Location: Canada
Posted: July 05, 2005 at 1:14 PM / IP Logged  
wirewise wrote:
Mad Scientists wrote:
AC flows on the surface of the wire, DC flows through the wire..
I was taught that electricity (AC and DC) flows on the surface of the conductor (wire). Do you have any reference to this?
~wirewise~
I also carry the same concept as you wirewise until now. Great post Mad Sciencetist. Thanks.
Be careful whose advice you buy, but be patient with those who supply it.The New Guy's quick questions. -- posted image.
95oakmax 
Member - Posts: 3
Member spacespace
Joined: June 29, 2005
Location: United States
Posted: July 05, 2005 at 2:50 PM / IP Logged  
Mad Scientists,
So basically you are confirming my belief that the strand-count in car wiring is only beneficial in terms of flexibility in the wire itself, am I correct?
-Jonathan
1995 Maxima GLE-JVC AR-5000 HU-Polk dB6750 Comps-Polk dB675 Coax-SoundSplinter RL-i 10"-Powered by MTX
Page of 2

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, March 28, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer