the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

bazooka el8a in a 2004 ford f150


Post ReplyPost New Topic
< Prev Topic Next Topic >
cavtrooper06 
Member - Posts: 2
Member spacespace
Joined: February 13, 2008
Location: Missouri, United States
Posted: February 13, 2008 at 9:24 PM / IP Logged  

First of all, if your reading this thank you for taking the time to help.  I've search on this site, the SAS Bazooka website, and others in order to correctly wire up my bass tube for installation.

My truck is a 2004 Ford F150 (new body style) with the stock headunit and stereo system.

Off this website I discovered this, the wiring harness to the HU diagram:

Radio 12v lt. GREEN/ purple   +   radio harness

Radio Ground black and BLACK/ lt. green   -   radio harness
Radio Ignition pink/black or lt. GREEN/ YELLOW +   radio harness
Radio Illumination lt. blue/red (dimmer)   +   radio harness
Factory Amp Turn-on dk. GREEN/ purple   +   radio harness
Notes: This is the subwoofer amplifier turn on lead. The subwoofer and amp are in the driver side rear corner of the cabin. The subwoofer speaker wires are BROWN / orange (+), and RED / black (-) at the radio harness.
Power Antenna N/A       
LF Speaker +/- ORANGE / lt. grn - lt. blue/wht   +,- radio harness
RF Speaker +/- WHITE/ lt. grn - dk. GREEN/ org   +,- radio harness
LR Speaker +/- gray/lt. blue - tan / YELLOW   +,- radio harness
RR Speaker +/- ORANGE / red - BROWN / pink   +,- radio harness

I have a line-level converter (LLC), but what I am unsure of is which wires I should connect to which.  The LLC has four wires right(+), right(-), left (+), and left(-); do these wires get connected to the LF and RF speaker wires?  For instance my LLC right(+) would be connected to the RF speaker WHITE/ lt. grn wire and the right(-) and the right(-) to the RF speakerdk.GREEN/ orange wire? 

The bazooka tube wiring has both RCA plugs (female) and the wiring for the high and low inputs; so once I install the LLC (which also has RCA female plugs) would I only need to connect the RCA plugs from the LLC to the wiring harness RCAs via a double male ended RCA cable?

Lastly, concerning the tubes power source, if I wanted the tube to be powered when I have the key in would it be advisable to connect it the Radio Ignition pink/black or lt. GREEN/ YELLOW wire or is there a better solution?

Again thank you for any insight.

stevdart 
Platinum - Posts: 5,816
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Mobile Audio and Video. Click here for more info.spaceThis member consistently provides reliable informationspace
Joined: January 24, 2004
Location: Pennsylvania, United States
Posted: February 13, 2008 at 11:28 PM / IP Logged  

wrote:
I have a line-level converter (LLC)

Call it a LOC and everybody will be on the same page.  Line output converter.

wrote:
The LLC has four wires right(+), right(-), left (+), and left(-); do these wires get connected to the LF and RF speaker wires? 

Yes.  Or you can connect directly onto the speaker terminals (if the doors are opened up) and not have to mess around with locating OEM speaker wire colors.  Use common speaker wire and run it to the LOC location near the amp.

wrote:
The bazooka tube wiring has both RCA plugs (female) and the wiring for the high and low inputs; so once I install the LLC (which also has RCA female plugs) would I only need to connect the RCA plugs from the LLC to the wiring harness RCAs via a double male ended RCA cable?

It is common practice to use a short length of RCA wire (which has male plugs on both ends) to connect the LOC to the amplifier.  So, yes.

wrote:
if I wanted the tube to be powered when I have the key in would it be advisable to connect it the Radio Ignition pink/black or lt. GREEN/ YELLOW wire or is there a better solution?

Connect to any 12V switched wire under the dash.  Find if switched by metering the wire with your meter's red lead while the black lead is grounded to chassis.  The meter will show ~12 DC volts with the switch turned to ACC or ON, but will show nothing if the ignition switch is off.  Sometimes a switched wire may be found close to the sub's mounting location, so probe that area first.  Once you have established the turn on wire connection and soldered it into place, fuse the turn on wire with a 1 amp fuse.

Build the box so that it performs well in the worst case scenario and, in return, it will reward you at all times.
cavtrooper06 
Member - Posts: 2
Member spacespace
Joined: February 13, 2008
Location: Missouri, United States
Posted: February 14, 2008 at 6:17 AM / IP Logged  

Stevdart...thank you.  As you can probably tell I don't wire things up much and you have eliminated all my confusion.  I appreciate it.


Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Friday, March 29, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer