eclipse xa5000 vs phoenix gold xs6600

Home / the12volt's Install Bay / Car Audio / eclipse xa5000 vs phoenix gold xs6600 (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

uberspeed

Member - Posts: 11

Joined: November 07, 2007

Location: Florida, United States

Posted: November 07, 2007 at 6:18 PM / IP Logged

Hello folks, new here. I searched and came up with nothing so I'm asking here.

So it looks like I'm down to these two, which would you buy and why? :)

Both are about $300-325 so it's not a consideration really.

Eclipse XA5000

http://www.eclipse-web.com/amp/xa5000.html

Specs:

Phoenix Gold XS6600

http://www.phoenixgold.com/webfaq/XS.htm

Specs:

Thermally Efficient Heatsink Timed Acoustically Integrated Muting (TAIM)

Differential Speaker or RCA Level Inputs

Tri-Linear Capability Allows Simultaneous Stereo and Bridged Operation

24dB / Octave High Pass and Low Pass Crossover

Rnet Programmable 20Hz to 20kHz Crossover Frequency

Auxiliary Outputs Route Full Range Signals

Variable Bass Boost Circuit Provides Up to 18 dB of Boost at 45 Hz

2 Ohm Bridged Stable

Output Power:

4 ohm stereo @ 12/13.8 VDC: 18/50 WRMS x 4

2 ohm stereo @ 13.8 VDC: 90 WRMS x 4

4 ohm bridged @ 13.8 VDC: 180 WRMS x 2

Subwoofer Channel Output Power:

4 ohm stereo @ 12/13.8 VDC: 25/75 WRMS x 2

2 ohm stereo @ 13.8 VDC: 150 WRMS x 2

4 ohm bridged @ 13.8 VDC: 300 WRMS x 1

Crossover Frequencies: 20Hz to 20kHz(Rnet factory set at 100Hz)

Crossover Slopes: 24dB per Octave

Frequency Response: +/-1dB from 20Hz to 20kHz

Signal to Noise Ratio: >100dB

Input Sensitivity: 200 millivolts to 2 volts

Input Impedance: >10k ohms

Input Voltage Range: 10.5 volts to 15.0 volts

Bass EQ: 0 to + 12dB @ 45Hz

Typical current draw at idle: 750 milliamps

Minimum Impedance: 2 ohm bridged/1ohm stereo

Dimensions: 14.25L x 11.25W x 2.1H

So in reading this: https://www.the12volt.com/installbay/forum_posts.asp~TID~75836~PN~1

Is efficiency more important or Signal to Noise Ratio?

Provided I read correctly and did the formulas right:

The Eclipse has 46% efficiency with >90% Signal to Noise Ratio.

The PG has 43% efficiency with >100 Signal to Noise Ratio.

In looking them over closely the Eclipse is much more configurable, in terms of crossover points and bass boost. Just trying to make sure I get the right gear...

Please help me decide and thank you all in advance for educating me.

uberspeed

Member - Posts: 11

Joined: November 07, 2007

Location: Florida, United States

Posted: November 07, 2007 at 8:28 PM / IP Logged

The rest of the setup:

Vehicle: 2008 Scion xB2

HU: Pioneer AVIC D3

Front and Rear: eD eDi 6000s v.2 http://www.edesignaudio.com/edv2/product_info.php?cPath=21&products_id=49

Sub:

eD enclosure http://www.edesignaudio.com/edv2/product_info.php?cPath=1_78_79&products_id=655

Single 13" http://www.edesignaudio.com/edv2/product_info.php?cPath=21&products_id=31

Thanks!

stevdart

Platinum - Posts: 5,816

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Mobile Audio and Video. Click here for more info.

This member consistently provides reliable information

Joined: January 24, 2004

Location: Pennsylvania, United States

Posted: November 07, 2007 at 9:20 PM / IP Logged

Eclipse is known to adhere to higher standards than Kleenex Gold. I'd love to have an Eclipse in my car.

Build the box so that it performs well in the worst case scenario and, in return, it will reward you at all times.

DYohn

Moderator - Posts: 10,741

This member has been recognized as an authority in Electrical Theory. Click here for more info.

Joined: April 22, 2003

Location: Arizona, United States

Posted: November 07, 2007 at 10:21 PM / IP Logged

Eclipse, no question.

Support the12volt.com

haemphyst

Platinum - Posts: 5,054

Joined: January 19, 2003

Location: Michigan, Bouvet Island

Posted: November 08, 2007 at 10:45 AM / IP Logged

DYohn wrote:

Eclipse, no question.

Ditto

It all reminds me of something that Molière once said to Guy de Maupassant at a café in Vienna: "That's nice. You should write it down."

uberspeed

Member - Posts: 11

Joined: November 07, 2007

Location: Florida, United States

Posted: November 08, 2007 at 5:02 PM / IP Logged

4 gauge amp kit, 80A fuse. (sized right?)

14 gauge for sub. (should I use 12?)

16 gauge for speakers. (should I use 14?)

X-over points:

Front and Rear: Hi-Pass 30-500Hz (where would you set it?)

Sub: Lo-Pass 50-500Hz (where would you set it?)

Bass Boost 32-64Hz up to 8db (where would you set it? would you even use it?)

forbidden

Platinum - Posts: 5,352

Joined: November 01, 2003

Location: Alberta, Canada

Posted: November 08, 2007 at 7:31 PM / IP Logged

Eclipse again, no questions, do not pass go. The amp has 3 30amp fuses in it so ideally a larger fuse on the main power line if you could. The speaker wire size will be fine, no harm in going a little bit larger though. Low pass the subs to start around 110 and hp the front and rears around the same area, maybe a little lower. Play with the crossover points with the sub off to see how it changes at all volume levels.

Top Secret, I can tell you but then my wife will kill me.

uberspeed

Member - Posts: 11

Joined: November 07, 2007

Location: Florida, United States

Posted: November 08, 2007 at 8:10 PM / IP Logged

It's 25Ax3 on the fuses, so I figured an 80A fuse would be right, or am I wrong? In reading the FAQ I thought that was right.

This is the kit I'm looking to go with, it gives me 30ft of 12 gauge for the sub and I should use 14 for the speakers then?

Amp kit, 4 gauge: http://www.ikesound.com/product-product_id/6854

Power OFC Cable [4 gauge/20 ft]

Ground OFC Cable [4 gauge/3 ft]

Double Shielded RCA OFC Cable [17 ft]

Clear OFC Speaker Wire [12 gauge/30 ft]

Remote Turn-on Wire [17 ft]

Split Looom tubing [6 ft]

1 x AGU Fuse Holder

1 x AGU Fuse [80 Ampere]

2 x Ring Terminal [4 gauge]

2 x Spade Terminal [4 gauge]

2 x Spade Terminal [16 gauge]

2 x Butt Connector

10 x Cable Ties

2 x Self-tapping Screw

uberspeed

Member - Posts: 11

Joined: November 07, 2007

Location: Florida, United States

Posted: November 08, 2007 at 8:17 PM / IP Logged

Speakers Front and Rear: eD 6000s v.2

65W RMS 50Hz-20KHz 4OHM 91dB

Sub: still getting specs

So I should start at 110Hz and go from there? No over lap on the Hz?

uberspeed

Member - Posts: 11

Joined: November 07, 2007

Location: Florida, United States

Posted: November 08, 2007 at 8:18 PM / IP Logged

And YES, I'm going with the Eclipse.

Thank you for that ;)

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.