the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

bike alarm


Post ReplyPost New Topic
< Prev Topic Next Topic >
blackeye_cis 
Member - Posts: 6
Member spacespace
Joined: March 19, 2007
Location: Singapore
Posted: June 13, 2010 at 4:23 AM / IP Logged  
Guys, need help.... simple diagram appreciates.
trying to build a "manual" alarm on my bike. Basically, I need a trigger switch that will activate the horn when the bike is off the main stand and "arm" when its on its main stand. And can only be reset with a hidden reset button.
Thank you all..............
blackeye_cis 
Member - Posts: 6
Member spacespace
Joined: March 19, 2007
Location: Singapore
Posted: June 13, 2010 at 4:24 AM / IP Logged  
Btw, I'm riding Honda ST 1300 07'
awdeclipse 
Copper - Posts: 285
Copper spacespace
Joined: August 05, 2007
Location: Michigan, United States
Posted: June 13, 2010 at 8:28 AM / IP Logged  
Does your bike have a factory Main Stand switch? Do you know if its ground or positive?
Last bike wiring schematic I looked at I believe both the main stand switch and clutch switch are in series that connect ground to the starter relay, and the starter button provides the +12v to the other side of the starter relays.
Depending on how the main stand switch is wired you may be able to use it as is to provide a switched ground. If your horn switch is also a ground switch, then you can wire the kick stand switch to your horn circuit so when the kickstand is up it honks the horn.
A hidden "arming switch" is your best bet to arm and disarm the system. You'll have to add a relay to power the horn while the ignition is off also.
Assuming main stand switch is GND:
Switched GND ---------> GND of Horn
Relay Pin 85-> GND
Relay Pin 86-> +12v from arming switch
Relay Pin 87-> Fused +12v
Relay Pin 30-> +12v to horn
Arming Switch:
Pin1 -> Fused +12v
Pin2 -> Relay 86
Summary: With the switch Armed, the relay will provide the horn with +12v and when the bike comes off the stand, the stand switch will provide ground to the horn. Depending how small of a switch you want to use, you could most likely get away with skipping the relay all together.
blackeye_cis 
Member - Posts: 6
Member spacespace
Joined: March 19, 2007
Location: Singapore
Posted: June 13, 2010 at 11:06 AM / IP Logged  
Thank you for the prompt reply...
It took awhile for me to digest it....Fyi, the main stand is not wired, only the side stand (-). Base on your explanation, is my schematic drawing correct?
http://www.facebook.com/?sk=2361831622#!/photo.php?pid=1109676&o=all&op=1&view=all&subj=125723977438868&aid=-1&id=1056191910
awdeclipse 
Copper - Posts: 285
Copper spacespace
Joined: August 05, 2007
Location: Michigan, United States
Posted: June 15, 2010 at 2:24 AM / IP Logged  
Sorry,
I don't use facebook.
Can you post the schematic in the forum for myself and others to check for you?
blackeye_cis 
Member - Posts: 6
Member spacespace
Joined: March 19, 2007
Location: Singapore
Posted: June 17, 2010 at 12:10 PM / IP Logged  
bike alarm -- posted image.
Hope you can view this...thx
blackeye_cis 
Member - Posts: 6
Member spacespace
Joined: March 19, 2007
Location: Singapore
Posted: June 17, 2010 at 12:19 PM / IP Logged  
http://www.flickr.com/photos/51246748@N04/4709010393/
Cant seems to upload the image file
oldspark 
Gold - Posts: 4,913
Gold spacespace
Joined: November 03, 2008
Location: Australia
Posted: June 17, 2010 at 9:41 PM / IP Logged  
Shorten the filename. 8 letters is fine, maybe 10 or so.
oldspark 
Gold - Posts: 4,913
Gold spacespace
Joined: November 03, 2008
Location: Australia
Posted: June 17, 2010 at 9:48 PM / IP Logged  
IMO that diagram is a silly arrangement - the Main Stand Switch should be grounding the relay's #85.
(If it wasn't for the disarming requirement, based on that diagram I'd omit the relay...)
And of course the +12V is fused...
sarfraz 
Member - Posts: 1
Member spacespace
Joined: August 30, 2010
Location: Pakistan
Posted: August 30, 2010 at 4:24 AM / IP Logged  
I want to install 10mm (diameter) LED  ( one or four) for additional light and would like to know the circuit diagram and components.
pakistanzindabad
Page of 2

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, March 28, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer