the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

How to Bypass a PATS


Post ReplyPost New Topic
< Prev Topic Next Topic >
roma66mx 
Member - Posts: 10
Member spacespace
Joined: May 07, 2002
Location: Mexico
Posted: July 05, 2002 at 1:48 PM / IP Logged  

 Hi , I want to know how can I bypass a PATS to the FORD Explorer 2000 , I will conect a remote starter , please send me a diagram . Thank you .

Velocity Motors 
Moderator - Posts: 12,488
Moderator spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Fabrication. Click here for more info.spaceThis member has been recognized as an authority in Mobile Audio and Video. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: March 08, 2002
Location: Manitoba, Canada
Posted: July 05, 2002 at 8:59 PM / IP Logged  

You will need a PATS bypass module and an extra key to introduce the proper resistance to the PATS computer.

  • The RKE is a Remote Keyless Entry
  • The factory disarm is ( - ) input signal

The PATS bypas system is easy ... take a relay ( 30/40 amp ) and hook it up like this:

  • 86 - Primary ignition ( BLUE/GREEN )
  • 85 - Ground out when running on remote starter
  • 87 - Key cylinder( wrap a 22 gauge wire around the key cylider column about 8 - 10 times and connect to pin 87 . This wire must be 20 - 24 gauge otherwise it will not introduce the signal into the PATS properly and you will get hit and miss starts.
  • 30 - Spare key with resistor in the black molded top part. You must wrap the the same wire that goesinto pin 87 around this key about 8 - 10 times as well and connect to pin 30.

I hope this is easy to follow and if not let me know and I will put up a picture of this circuit for you later.

Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Chris Luongo 
Platinum - Posts: 3,746
Platinum spaceThis member consistently provides reliable informationspace
Joined: May 21, 2002
Location: Massachusetts, United States
Posted: July 05, 2002 at 9:01 PM / IP Logged  

Four ways to do it, from best to worst:

1.  Go to any Directed Electronics (DEI) dealer and pick up DEI's 555F.  It will bypass PATS during remote start, and you don't have to give up any of your keys.  It comes with instructions.  When programming the 555F to your car, you need TWO working Ford keys.  www.directed.com

2.  Buy any of the universal bypass modules out there.  DEI 555U, Audiovox AS-TCBM, et cetera.  You will need to permanently install one of your Ford keys into the universal module, and those keys usually aren't cheap.

3.  You can make your own hand-made 555U with a relay and some scrap wire, but it can be hard for a novice installer to get this to work properly.

4.  Pry the little plastic plug out of your key head; the PATS capsule will fall out.  Glue the capsule to the ignition cylinder.  (You'll have to experiment to find a spot that will work.)  You'll also have to remove the capsules from all your spare keys, since the car won't start if it sees two capsules at once.  This method is cheap and easy, but your car is unprotected against theft.  And if that capsule comes unglued, the car won't start, not even with the key.


Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Friday, March 29, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer