the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

05 toyota celica gt, remote start wiring


Post ReplyPost New Topic
< Prev Topic Next Topic >
hammer16 
Member - Posts: 2
Member spacespace
Joined: February 21, 2008
Location: Virginia, United States
Posted: February 21, 2008 at 1:42 PM / IP Logged  
looking for wiring harness/diagrams to install remote start for 05 celica gt
KarTuneMan 
Platinum - Posts: 7,056
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member consistently provides reliable informationspace
Joined: December 14, 2004
Location: Isle Of Man
Posted: February 21, 2008 at 8:14 PM / IP Logged  
12 VOLTS White Ignition switch harness   + 
 The ignition switch wires change color through a connector on the steering column. Check both sides of the connector for these colors.
 IGNITION BLACK/ orange Ignition switch harness   + 
 The ignition switch wires change color through a connector on the steering column. Check both sides of the connector for these colors.
 IGNITION 2 Blue/red Ignition switch harness   + 
 The ignition switch wires change color through a connector on the steering column. Check both sides of the connector for these colors.
 ACCESSORY Gray      
 The ignition switch wires change color through a connector on the steering column. Check both sides of the connector for these colors.
 STARTER BLACK/ white Ignition switch harness   + 
 You may need to add a relay to isolate the starter and ignition wire during remote start since these wires are common when the ignition switch is off. See the TIP diagram.
 KEY SENSE Yellow pin-9 on 25-pin plug at Body ECU   - 
 The Body ECU is located in the center console in front of the shifter, mounted to the junction block. Remove the plastic cover from the right side of the console to access, or remove the trim plate around the shifter.
 TACH SIGNAL See notes     
 Remove the plastic cover on the engine to expose the 4 coils on the top rear of the engine block. Each coil has a BLACK/ white, blue / YELLOW and brown. Use the 4th wire at any of the coils for a tach reference. You can also use the BROWN / WHITE pin-27 on a 28-pin plug at the ECM located in the plastic case in front of the battery. This wire can also be found on the junction connector behind the plastic panel on the left side of the center console.
 LOCK PURPLE / white pin-15 on 22-pin plug at Body ECU   - 
 The Body ECU is located in the center console in front of the shifter, mounted to the junction block. Remove the plastic cover from the right side of the console to access, or remove the trim plate around the shifter.
 UNLOCK Pink/black pin-16 on 22-pin plug at Body ECU   - 
 The Body ECU is located in the center console in front of the shifter, mounted to the junction block. Remove the plastic cover from the right side of the console to access, or remove the trim plate around the shifter.
 DOORPIN RED / white pin-10 on 25-pin plug at Body ECU   - 
 The Body ECU is located in the center console in front of the shifter, mounted to the junction block. Remove the plastic cover from the right side of the console to access, or remove the trim plate around the shifter.
 TRUNK PIN Lt.GREEN/ gray dots pin-22 on 22-pin plug at Body ECU   - 
 The Body ECU is located in the center console in front of the shifter, mounted to the junction block. Remove the plastic cover from the right side of the console to access, or remove the trim plate around the shifter.
 BRAKESWITCH GREEN / WHITE At switch above brake pedal   + 
 PARKLIGHTS Dk.green At parklight relay in right side of center console   + 
 HAND BRAKE RED / black pin-19 on 22-pin plug at Body ECU   - 
 The Body ECU is located in the center console in front of the shifter, mounted to the junction block. Remove the plastic cover from the right side of the console to access, or remove the trim plate around the shifter.
 HORN Blue/black pin-14 on 25-pin plug at Body ECU   - 
 The Body ECU is located in the center console in front of the shifter, mounted to the junction block. Remove the plastic cover from the right side of the console to access, or remove the trim plate around the shifter.
 CLUTCH SWITCH BLACK/ white At switch on clutch pedal bracket   TYPE 2 

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, April 25, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer