the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

silverado 2007 no crank remote start


Post ReplyPost New Topic
< Prev Topic Next Topic >
tenoch_r 
Member - Posts: 3
Member spacespace
Joined: December 21, 2009
Location: Oklahoma, United States
Posted: December 21, 2009 at 7:16 PM / IP Logged  
Installing Bulldog RS1200 remote start using DEI PKUCG2X bypass, truck will not crank, everything powers up, just no crank. I have not installed the resistor in the starter wire hooked to pink/black resistor wire, will this prevent starting? Also the remote start does not have a second accessory wire to hook to pink/black resistor wire, do I use the main accessory wire out of RS that is hooked to the acc wire at ignition harness or can I use the 2nd ignition wire out of the RS instead? (also do I have to put the resistor in this wire?). Lots of questions, but 1/2 of the info I find says don't need the resistors, 1/2 says they are needed. I don't care if the ECM records the error code, I just want the starter to work. Thanks!
tenoch_r 
Member - Posts: 3
Member spacespace
Joined: December 21, 2009
Location: Oklahoma, United States
Posted: December 22, 2009 at 11:07 PM / IP Logged  
Well I added resistors to ignition wire hooked to pink/blk resistor wire, truck now remote starts, runs a few seconds then dies, guess tomorrow I'll add resistors to the 2nd acc wire, some documentation says this will solve the problem, but once again, some say it's something else. When I get this done post I'll post a list of connections that worked for me.
jjnemoiii 
Member - Posts: 8
Member spacespace
Joined: December 13, 2009
Posted: December 23, 2009 at 3:53 PM / IP Logged  
Does your starter have some sort of way to determine why it shut down?  I have the python 14000XPL, and through a series of steps it will tell you why the R/S shut off last time, Whether the brake was pressed, shutoff by remote, Etc.  Maybe that will also lead you in the right direction, if the resistor does not help.
tenoch_r 
Member - Posts: 3
Member spacespace
Joined: December 21, 2009
Location: Oklahoma, United States
Posted: December 23, 2009 at 7:36 PM / IP Logged  
I'll have to check, Bulldog has poor customer support and even worse install instructions. I've been trying to set the RS tach mode to on, but can't get it to do so, when I go through the sequence I just get a series of 5 flashes of the park lights, not the series of flashes listed in the manual.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, March 28, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer