2011 Jeep Wrangler 4D w/ Viper 5706v & DBALL2

OK, so I purchased the following Viper 5706V DBALL2 T-Harness and misc sensors.. I have a 2011 Jeep Wrangler Unlimited. I got everything installed and wired up per the documentation but it appears there may be discrepancy's in RSR / DBALL2 / Wiring. It appears to me that the RSR is no longer supported by DBALL2 and that either the XL202 or the Smart Start has to be purchased? Everything is working for me except the remote start... I have switched the 5706 into automatic mode VIA the menus and I get the 8 alerts indicating "Neutral safety wire has no ground or the neutral safety switch is Off" when I attempt to do remote start. I have verified the safety switch is in the on position and that the BLACK/ white wire from the 24 pin aux harness is connected to ground with all my other ground wires. Any ideas what I am doing wrong? Been beating my head against the wall for 2 days. Wiring information below. Thanks! Items below are what I connected 1. +12v constant from battery 2. Ground 3. Siren red wire 13. Ground 2. +12v constant from battery 5. +12v constant from battery 10. Connected to pink/white wire in the 8 pin ignition harness Door Lock, 3-pin connector Not Used I am using the D2D port to a DBALL2 flashed with a standard install Sensor 1 = Shock Sensor Sensor 2 = 508d proximity sensor Link to the wiring diagram

Also connected the pink wire from the CHTHD2 t-harness to the pink / white wire of the ignition harness. Additional notes: When I attempt to remote start with just the DBALL2 using the 3x door lock, I get 7 red flashes on the DBALL2. When I hook up the Viper 5706v and connect the D2D cable to the DBALL2 and attempt to do remote start with the viper remote I get 8 clicks from the Viper unit.

I would start with testing the switch. Make sure you have ground on both sides of it.Nissan Master Tech.

I believe Directed dropped support of the 3X lock remote start option last year.

The only thing I see wrong with your wiring is your use of the Vipers' Pink/White IGN2 Output wire for the connection to the CHTHD2

( R9 - R10 ) t-harness Pink wire. You need to use the solid Pink IGN1 Input/Output wire from the Viper for that connection.

Soldering is fun!

mpe235 wrote: I would start with testing the switch. Make sure you have ground on both sides of it.

Can you provide more info? Thanks.

kreg357 wrote: I believe Directed dropped support of the 3X lock remote start option last year. The only thing I see wrong with your wiring is your use of the Vipers' Pink/White IGN2 Output wire for the connection to the CHTHD2 ( R9 - R10 ) t-harness Pink wire. You need to use the solid Pink IGN1 Input/Output wire from the Viper for that connection.

That is what I thought as well but I have seen conflicting info. https://www.directechs.com/repository/slides/3X-LOCK-START.gif https://www.directechs.com/vagbyfunction.aspx?fn=183 I did try connecting the pink wire from the t-harness as well. It did not work either.

Read that last one wrong, I have tried both combos. pink wire from t-harness to pink/white pink from viper to pink/white and both connected. No combination seems to work.

8 flashes is the neutral safety. Check that the BLACK/ White aux harness 24-pin is grounded. Also that stand alone witch is grounding when turned on.

BTW the 3x RS is back as of yesterday. LOL https://www.directechs.com/news.aspx?newsid=24

icearrow6 wrote: 8 flashes is the neutral safety. Check that the BLACK/ White aux harness 24-pin is grounded. Also that stand alone witch is grounding when turned on.

Yea, verified that like 10x no joy..

icearrow6 wrote: BTW the 3x RS is back as of yesterday. LOL https://www.directechs.com/news.aspx?newsid=24

Seriously... this wasn't there yesterday... Arrrrrr.. will try again... let you know.

IUVR&^#(&* It works now.............. Thx guys... Very frustrating....