the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

Compustar CM900S, 1997 Toyota 4Runner


Post ReplyPost New Topic
< Prev Topic Next Topic >
derekasia 
Member - Posts: 1
Member spacespace
Joined: February 01, 2021
Location: Virginia, United States
Posted: February 01, 2021 at 1:09 PM / IP Logged Link to Post Post Reply Quote derekasia
Had some questions as I'm getting ready to do the remote start install in my 97' 4runner. I'd like to get remote start as well as keyless entry. It does have power locks. I am installing a CM900S from Compustar.
Here's the wiring below with what I have and what I have questions on, please correct anything that you believe might be wrong. I've put in parenthesis the ones I'm unsure about.
12 V constant - White wire found in ignition
(12 V Light - Curious on if this wire is even needed? Or this just another accessory wire?)
12 V constant - White/Red wire found in ignition
12V accessory - Blue/Red wire found in ignition
(Selectable by Jumper Iginition - Black/Red wire found in ignition)
12 V Starter - Black wire found in ignition
12 V ignition (output/input) - Black/Yellow wire found in ignition
Ground - (Will tie into grounded nut)
Parking Light Output - Green wire found below fuse panel
Lock output - Red/White wire found left of fuse panel
Unlock output- Red/Yellow wire found in left of fuse panel
(Status output - Is this have to be used?)
(Rearm output - Not used?)
(Disarm output - Not used?)
Horn output - Green/Red wire in steering column
Foot Brake Input - Green/White wire in brake switch
(- Trigger Starter Input- Not used?)
(+ Trigger Starter Input- Not Used?)
Tach/ALT sensing input - Black wire in OBD2 plug
Derek D
kreg357 
Platinum - Posts: 7,781
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: January 30, 2009
Location: Pennsylvania, United States
Posted: February 01, 2021 at 2:20 PM / IP Logged Link to Post Post Reply Quote kreg357
Some very minor updates. I used the (-) Parking Light wire instead of the (+) Parking Light wire you listed. It's possible the Tach can be found in the OBD2 plug, just test that Black wire to be sure. Check the jumper for IGN2 to ensure it's set for IGN.
CM900-s to 1997 4Runner
CN1
Pin 1 Red - Constant 12V.....................................WHITE (+)    @ IGNITION SWITCH HARNESS
Pin 2 Green/White - Programmable Output.........Not Used
Pin 3 Red/White - Constant 12V..........................WHITE/RED (+)   @ IGNITION SWITCH HARNESS
Pin 4 White - Accessory 12V positive (+)..............BLUE/RED (+)     @ IGNITION SWITCH HARNESS
Pin 5 Blue - Programmable Output..set to IGN2..BLACK/YELLOW (+) or BLACK/RED (+)     @ IGNITION SWITCH HARNESS
Pin 6 Yellow - Starter 12V positive (+)...................BLACK (+)     @ IGNITION SWITCH HARNESS
Pin 7 Green - Ignition 12V positive (+)...................BLACK/YELLOW (+)     @ IGNITION SWITCH HARNESS
Pin 8 Black - Ground negative (-) input..................Chassis Ground
CN3
Pin 1 Green/White - (fixed) Parking light 250mA (-) output..................RED/WHITE (-)      @ STEERING COLUMN HARNESS
Pin 2 Blue/Lt. Green - [POC 2] Lock 250mA, 800mS (-) output...........RED/WHITE (TYPE B)     @ 10-PIN PLUG, LEFT OF FUSEBOX
Pin 3 Blue - [POC 3] Unlock 250mA, 800mS (-) output........................RED/YELLOW (TYPE B)     @ 10-PIN PLUG, LEFT OF FUSEBOX
Pin 4 Black - [POC 4] (GWR) 250mA latched negative (-) output.............................Not Used
Pin 5 Orange - [POC 5] Factory Alarm Arm 250mA, 800mS (-) output....................Not Used
Pin 6 Orange/White - [POC 6] Factory Alarm Disarm 250mA, 800mS (-) output....Not Used
Pin 7 White - [POC 7] Horn\ 250mA (-) output...........................................................GREEN/RED (-)    @ STEERING COLUMN HARNESS
Pin 8 Gray/Black - Hood Pin negative (-) (default setting) input..................................Kit supplied hood pin
Pin 9 Light Blue/White - Brake 12V positive (+) input........................GREEN/WHITE (+)     @ SWITCH ABOVE BRAKE PEDAL
Pin 10 RED/White - Trigger start (-) input..........................................Not Used
Pin 11 RED - Positive Trigger (+) input...............................................Not Used
Pin 12 Yellow/Black - Engine sensing input (A/C)...............................BLACK (AC)     @ IGNITOR or DIAGNOSTIC PLUG
Soldering is fun!

If you wish to post a reply to this topic, you must first login.
If you are not already registered, you must first register.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, March 28, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer