the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

Command Start CS2400


Post ReplyPost New Topic
< Prev Topic Next Topic >
CLangan 
Member - Posts: 8
Member spacespace
Joined: November 03, 2003
Location: Canada
Posted: November 03, 2003 at 7:36 AM / IP Logged  

Hello,

I have a Command Start CS2400 and transmitter CS-306. The problem I have is that when I press any button nothing happens. I do hear nose coming from the transmitter. How do I program the transmitter. I do have another one that works fine so I know the unit is find.

THanks

Clinton

Justaguy 
Copper - Posts: 112
Copper spacespace
Joined: October 31, 2003
Location: Canada
Posted: November 03, 2003 at 6:43 PM / IP Logged  
to program a new remote, flash(press the hood pin switch down and release, and then imediatly after, tap it quickly) the pin switch, make sure the lights stay on for atleast 5 or 6 seconds, then hold button one until the lights go out. close the hood.
CLangan 
Member - Posts: 8
Member spacespace
Joined: November 03, 2003
Location: Canada
Posted: November 07, 2003 at 11:11 AM / IP Logged  

Thanks for the reply; Unfortually I still can't get it working. What happens is I press down the switch and the lights come on for 5 seconds and then goes off. I can't get the lights to come on soild. I do press the switch and then tap it quick but nothing. Any other suggestions

Thanks

Clinton

Justaguy 
Copper - Posts: 112
Copper spacespace
Joined: October 31, 2003
Location: Canada
Posted: November 07, 2003 at 10:29 PM / IP Logged  

Keep trying, it's tricky. as soon as you release the switch, tap it all the way down and back really quick.

it'll work, trust me.

CLangan 
Member - Posts: 8
Member spacespace
Joined: November 03, 2003
Location: Canada
Posted: November 10, 2003 at 8:05 AM / IP Logged  

THanks,

Yes your correct, it's tricky and I finally got it.

Thanks again

Clinton

CLangan 
Member - Posts: 8
Member spacespace
Joined: November 03, 2003
Location: Canada
Posted: January 19, 2004 at 8:39 AM / IP Logged  

Hello,

My command start failed and now flashes 9 times. I have seen that you just disconnect the battery terminal and this will clear the code.

This can't be the only way of clearing the code. Does anyone know if there is a way using the engine switch and the remote control. I have seen this done before but can't remember.

Thanks

Clinton


Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Friday, March 29, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer