the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

04 Sienna unlock wire


Post ReplyPost New Topic
< Prev Topic Next Topic >
thousandandone 
Member - Posts: 31
Member spacespace
Joined: September 20, 2004
Location: Canada
Posted: October 19, 2004 at 6:04 PM / IP Logged  

Hello,

I try to install the Compustar 2WAS module (CM3000) into 04 Toyota Sienna. The problem I have right now is , I can't locate the power Unlock wire. According to wiring diagram is BLUE, but it shows 0V at all time even when I rotate the key from LOCK to UNLOCK . I did find the power lock wire . It is LIGHT GREEN.

Does anyone experiences , Idea , Opinions. Please help me to locate this wire

THANK YOU

By the way, The accessories wire is BLACK / YELLOW( small wire) NOT PINK as the wiring diagram says

Could someone please comfirm it ?

Autostar
Teken 
Gold - Posts: 1,492
Gold spacespace
Joined: August 04, 2002
Location: Aruba
Posted: October 19, 2004 at 6:25 PM / IP Logged  
You may also use the passenger door key cylinder wire for unlock. Wihich only requires a single pulse. It is blue / YELLOW (-) and can be located in the passenger kick in a 12 pin plug.
Regards
EVIL Teken . . .
mo12v 
Platinum - Nominee - Posts: 2,748
Platinum - Nominee spaceThis member consistently provides reliable informationspace
Joined: September 30, 2003
Location: Afghanistan
Posted: October 19, 2004 at 6:29 PM / IP Logged  

Sorry U R having difficulties, but not knowing how U wired your unit, I must have been making this mistake on ALL the Toyotas I have done.......Yeah right

As for your UNLock issue:  read note at bottom and try to understand

Ignition #2BLACK / YELLOW 18 GAGEIGNITION SWITCH HARNESS
Ignition #3
AccessoryPINKIGNITION SWITCH HARNESS

NOTE **    These 2 wires will ONLY meter (show a Ground or (-) Negative) when you place a key in the DRIVERS DOOR KEY CYLINDER (outside of drivers door) and rotating from Lock to Unlock. You must use a Double Pulse Unlock programming on this vehicle. For a Single Pulse Unlock you can use the wire in the Passengers kick panel in a 12 Pin Plug, it will meter off of the Passengers key cylinder, the wire is a BLUE / YELLOW (-).

MO
Don't Learn from Others Mistakes
You Might Be the One That Knows.
thousandandone 
Member - Posts: 31
Member spacespace
Joined: September 20, 2004
Location: Canada
Posted: October 19, 2004 at 6:57 PM / IP Logged  

Hi mo12V,

I'm really sorry for what I have said . I'm too new to this field. Please forgive me. what I meant is : I really don't know what the Ignition #2 mean . When I connected the PINK to accessory from module I didn't get the fan blow. But when I connect BLACK / YELLOW 18 GAGE to Accessory I got fan blow. I thought there is a mistake.

I have read the NOTE ** many many times and my understand is : I must have 12V at BLUE wire before trigger. When I place a key in the DRIVERS DOOR KEY CYLINDER (outside of drivers door) and rotating from Lock to Unlock. I must see a pulse Ground or (-) Negative. Please point me to the right direction if I'm wrong

Autostar
mo12v 
Platinum - Nominee - Posts: 2,748
Platinum - Nominee spaceThis member consistently provides reliable informationspace
Joined: September 30, 2003
Location: Afghanistan
Posted: October 19, 2004 at 7:15 PM / IP Logged  

If U have found the Lock wire in the Connector in Driver Kick Panel, the BLUE UNLock wire should also be there.

Have U tried a direct ground "touch" to the L/GREEN or BLUE wire to see if they respond?

Power LockL GREENDRIVERS KICK WHT 18 PIN CONN
Power UnlockBLUEDRIVERS KICK WHT 18 PIN CONN

You must use a Double Pulse Unlock if using BLUE wire

For a Single Pulse Unlock you can use the wire in the Passengers kick panel in a 12 Pin Plug, it will meter off of the Passengers key cylinder, the wire is a BLUE / YELLOW (-).

MO
Don't Learn from Others Mistakes
You Might Be the One That Knows.
thousandandone 
Member - Posts: 31
Member spacespace
Joined: September 20, 2004
Location: Canada
Posted: October 19, 2004 at 7:27 PM / IP Logged  

Thanks Man

 I'll will try that

Autostar
nava94 
Silver - Posts: 296
Silver spacespace
Joined: February 28, 2004
Location: United States
Posted: October 19, 2004 at 11:16 PM / IP Logged  
the lock/unlock wires are at the driver kickpanel
thousandandone 
Member - Posts: 31
Member spacespace
Joined: September 20, 2004
Location: Canada
Posted: October 19, 2004 at 11:59 PM / IP Logged  

Hi,

Let me explain what I have done :

The Light Green ( Lock ) connect to module . It's working good ( It's about 10V at rest and pulse to ground when trigger )

The Blue ( Unlock ) at driver kick and the Blue / YELLOW at passenger kick. They are both show 0V at all time. Trigger them to ground nothing happen

I did probe almost every single wire in driver & passenger kick to locate the unlock wire but still no luck

My next step is to open driver door panel to get the wire.

Any idea would be appreciated?

Thank You

Autostar

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Friday, March 29, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer