the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

window module, 2005 silverado


Post ReplyPost New Topic
< Prev Topic Next Topic >
hermanz71 
Member - Posts: 5
Member spacespace
Joined: July 10, 2005
Posted: July 26, 2005 at 3:27 PM / IP Logged  
iam having a problem with a smart window roll up/down module.i have it installed in a 2005 silverado and it does not work. it is definitly wired correctly. windows donot roll up or down, relays in module are clicking, but no action. windows work fine with factory switches. what is the problem? can someone help? and are windows posibly databus controlled? thanks
iskidoo 
Silver - Posts: 1,040
Silver spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: December 08, 2002
Location: Maine, United States
Posted: July 26, 2005 at 3:52 PM / IP Logged  
You cut each wire in two and spliced one side to the switch side and the other to the motor side. Is it possible that your wires are reversed for each window? This would supply power to the switch side each time you were trying to use the roll-ups (you want the motor side) but it would function normally when using the door switch.
Steve G
iskidoo 
Silver - Posts: 1,040
Silver spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: December 08, 2002
Location: Maine, United States
Posted: July 26, 2005 at 3:54 PM / IP Logged  
You used the following wire colors right?
LF Window up/dn dk. blue - brown   C   LF window switch in door     
RF Window up/dn dk. blue - brown   C   RF window switch in door     
LR Window up/dn dk. blue - brown   C   LR window switch in door     
RR Window up/dn dk. blue - brown   C   RR window switch in door
Steve G
hermanz71 
Member - Posts: 5
Member spacespace
Joined: July 10, 2005
Posted: July 26, 2005 at 8:41 PM / IP Logged  

already tried reversing switch/motor wires, nothing happened.

wire colors used right at the motor in each door

up - - blue +

down - - brown

Powermyster 
Silver - Posts: 962
Silver spacespace
Joined: April 06, 2005
Location: Ireland
Posted: July 27, 2005 at 3:38 AM / IP Logged  
did you test the wires to see if the module is putting out current
hermanz71 
Member - Posts: 5
Member spacespace
Joined: July 10, 2005
Posted: July 27, 2005 at 3:05 PM / IP Logged  
it says in the directions that the module cannot be bench tested. if it was supplying voltage the windows would move. the device is definately wired correctly , ive check it a few times. once it cools down a bit i will get back to it.
hermanz71 
Member - Posts: 5
Member spacespace
Joined: July 10, 2005
Posted: July 27, 2005 at 4:01 PM / IP Logged  
i think i just figured out the problem. both wires rest at + not negative. when activated both wires to motor are supplied with + 12v. i tested. and also removed wire that should be - and grounded as i activated module and windows moved. now only problem is to figure out what to do?
mo12v 
Platinum - Nominee - Posts: 2,748
Platinum - Nominee spaceThis member consistently provides reliable informationspace
Joined: September 30, 2003
Location: Afghanistan
Posted: July 27, 2005 at 9:00 PM / IP Logged  
This is  Data Link Power Windows.............But they are NOT that difficult
They are Reversal Rest At Ground Type Window Circuit .......
It appears you have a Ground problem or a reversed set of wires
MO
Don't Learn from Others Mistakes
You Might Be the One That Knows.
hermanz71 
Member - Posts: 5
Member spacespace
Joined: July 10, 2005
Posted: July 28, 2005 at 2:52 PM / IP Logged  
wires do not rest at ground. wires always are 12v + and the negative is switched. when module is activated both wires to each motor are getting positive. i think i figured it out. i ordered dei 530t which works by switching ground. thanks any way.
nava94 
Silver - Posts: 296
Silver spacespace
Joined: February 28, 2004
Location: United States
Posted: July 28, 2005 at 9:13 PM / IP Logged  
yeah better of with the 530t so you can set the polarity for the windows.plus it has the resistance swithches in case the window motor sucks and gets stuck it will roll it up.make sure you use two diodes to isolate the starter interrupt relay and window module from each other.good luck. 

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Friday, March 29, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer