the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

Urgently need 07 Escalade Wiring diagrams


Post ReplyPost New Topic
< Prev Topic Next Topic >
escalade007 
Member - Posts: 6
Member spacespace
Joined: June 20, 2006
Posted: June 20, 2006 at 7:50 PM / IP Logged  

Hi, I've been unable to locate any 07 Escalade electrical wiring diagrams. Can someone tell me where these are available from?

Also, does anyone know where the starter/kill wire switch is?

Thanks

chungo 
Copper - Posts: 135
Copper spacespace
Joined: December 31, 2003
Location: United States
Posted: June 20, 2006 at 8:32 PM / IP Logged  
12voltsRED / white (2A) + ignition harness
Notes: For high current 12V, use RED / black (60A) and RED / black (60A) at the fuse box, black 40 pin plug, pins F1 and E3, or go to the battery.
Starterwhite + ign harn or BCM, lt. grn plug, pin 4
Notes: Starter is positive trigger thru a 1300 ohm resistor.
The BCM (Body Control Module) is to the left of the steering column.
See DirectFax document 1605 for remote start interface information.
Second StarterN/A
Ignitionpink + ign harn or BCM, lt. grn plg, pin 14
Notes: The BCM (Body Control Module) is to the left of the steering column.
Second IgnitionN/A
Third IgnitionN/A
Accessorybrown + ign harn or BCM, lt. grn plg, pin 21
Notes: The BCM (Body Control Module) is to the left of the steering column.
Second AccessoryN/A
Keysensepink + ign harn or BCM, lt. grn plug, pin 2
Notes: The BCM (Body Control Module) is to the left of the steering column.
Power Locksee notes
Notes: To lock/unlock the driver door go to the driver door module or motor in the door and 5wi the tan (lock) and purple (unlock) motor wires.
To lock/unlock the passenger door go to the passenger door module or motor in the door and 5wi the tan (lock) and gray/black (unlock) motor wires.
To lock/unlock the rear doors use lt. blue (+) and white (-) at the BCM, gray plug, pins 7 and 9.
The BCM (Body Control Module) is to the left of the steering column.
Power Unlocksee power lock notes
Lock Motorgray 5wifuse box, black 14 pin plug, pin B4
Unlock Motorpurple 5wiDDM, brown 16 pin plug, pin 8
Notes: The DDM (Driver Door Module) is in the driver door.
Parking Lights+brown (L), brown (R) + underhood fuse box, blk 30 pin plug
Parking Lights-lt. blue - switch or BCM, natural plug, pin 8
Notes: The BCM (Body Control Module) is to the left of the steering column.
Hazardswhite - switch or BCM, lt. grn plug, pin 19
Notes: The BCM (Body Control Module) is to the left of the steering column.
Turn Signal(L)lt. blue/wht (F), yel/blk (R) + BCM, brown plug, pins 4 and 1
Notes: The BCM (Body Control Module) is to the left of the steering column.
Turn Signal(R)dk blu/wht (F), dk grn/wht (R) + BCM, blk plg, pin 5; brn plg, pin 2
Notes: The BCM (Body Control Module) is to the left of the steering column.
Reverse Lightdk. blue + BCM, natural plug, pin 22
Notes: The BCM (Body Control Module) is to the left of the steering column.
Door Triggersee notes - see notes
Notes: The LF door is gray/black at the DDM, brown 16 pin plug, pin 13. The RF door is BLACK/ white at the PDM, brown 16 pin plug, pin 13. The LR door is lt. blue/black at the BCM, pink plug, pin 15. The RR door is lt. GREEN/ black at the BCM, pink plug, pin 14. Use all four wires and diode isolate each.
The DDM (Driver Door Module) is in the driver door.
The PDM (Passenger Door Module) is in the passenger door.
The BCM (Body Control Module) is to the left of the steering column.
Dome Supervisiongray + BCM, natural plug, pin 5
Notes: The BCM (Body Control Module) is to the left of the steering column.
Trunk/Hatch Pinpink/black - BCM, pink plug, pin 12
Notes: The BCM (Body Control Module) is to the left of the steering column.
Hood Pinpink/black - pin sw or BCM, black plug, pin 17
Notes: The BCM (Body Control Module) is to the left of the steering column.
Trunk/Hatch Releasepink (glass), gray (gate) - BCM, pink plug, pins 24 and 13
Notes: Meter these wires while opening the liftglass or liftgate from the handle on the rear liftgate.
The BCM (Body Control Module) is to the left of the steering column.
On vehicles with the power liftgate, use dk. GREEN / WHITE (-) at the switch in the overhead console.
Power Sliding DoorN/A
Factory Alarm Arm
Factory Alarm Disarmlt. green - DDM, brown 16 pin plug, pin 4
Notes: Meter this wire while turning the key in the driver door key cylinder.
The DDM (Driver Door Module) is in the driver door.
Disarm No Unlockwith ignition and Passkey
TachometerNOT pink, brown, or black ac any ignition coil or fuel injector
Wait to startN/A
Brake Wirelt. blue/white + switch or BCM, brown plug, pin 6
Notes: Meter this wire while pressing the brake pedal with the ignition on.
The BCM (Body Control Module) is to the left of the steering column.
Parking Brakelt. blue - switch or BCM, brown plug, pin 16
Notes: The BCM (Body Control Module) is to the left of the steering column.
Horn Triggertan - switch or BCM, brown plug, pin 18
Notes: The BCM (Body Control Module) is to the left of the steering column.
Memory Seat 1orange + switch or DDM, blk 26 pin plg, pin 5
Notes: Memory seat 1 is positive trigger thru a 2260 ohm resistor. Memory seat 2 is positive trigger thru a 4260 ohm resistor.
The DDM (Driver Door Module) is in the driver door.
Memory Seat 2same as memory seat 1 wire +
Memory Seat 3N/A +
Urgently need 07 Escalade Wiring diagrams -- posted image.
Interface Module:Category:
Immobilizer Bypass
Required:
Yes
Type:
PASS-Key III+
Part #: 556UW
Alternate Part1 #: DesignTech 20402
Alternate Part2 #: DesignTech 29402
Notes: Standard on all models.
Urgently need 07 Escalade Wiring diagrams -- posted image.
Smart Starter Kill Relays:Relay Type:
Starter Relay
Location:
Engine compartment fusebox, Driver side
Part #: 6404A
escalade007 
Member - Posts: 6
Member spacespace
Joined: June 20, 2006
Posted: June 20, 2006 at 9:45 PM / IP Logged  
Does a schematic exist of the electrical?
integratyper934 
Copper - Posts: 150
Copper spacespace
Joined: April 01, 2006
Location: United States
Posted: June 20, 2006 at 10:24 PM / IP Logged  
the car runs on a lan system what exactly are you trying to do i heard some things about if you disconnect the radio youll have some problems. i know the factory overhead cant be used with an aftermarket head unit. what are u trying to accomplish?
escalade007 
Member - Posts: 6
Member spacespace
Joined: June 20, 2006
Posted: June 21, 2006 at 2:33 PM / IP Logged  

I'm trying to obtain information as to how to hook up equipment to it. One local dealer has given a story that he needs electrical schematics as he can't find the starter/kill switch to hook up a gps locator such as thewitness.net.

integratyper934 
Copper - Posts: 150
Copper spacespace
Joined: April 01, 2006
Location: United States
Posted: June 21, 2006 at 2:50 PM / IP Logged  
a dealer needs schematics??? what is it a contacted lo jack installer or soemthing
escalade007 
Member - Posts: 6
Member spacespace
Joined: June 20, 2006
Posted: June 21, 2006 at 3:05 PM / IP Logged  

If you visit the website it gives you all the details. It's more advanced the lojack. You're supposed to be able to disable the car from starting via the gps.

All I know is I've heard a bunch of excuses that the escalade is very electric and complicated.

bdl666 
Silver - Posts: 330
Silver spacespace
Joined: December 31, 2002
Location: United States
Posted: June 21, 2006 at 4:27 PM / IP Logged  

This is what chungo posted.  Just in its original form so you can print it.

http://directechs.com/directwire/print.asp?action=select&yr=6216&product=Remote%20Start

ieSpell rocks.
escalade007 
Member - Posts: 6
Member spacespace
Joined: June 20, 2006
Posted: June 22, 2006 at 11:20 PM / IP Logged  

Here's a good question. My dealer is trying to install the viper in the 07 escalade. Since the control module that controls door locks etc is not avail. for another 60-90 days for 07 model according to directed and 06 model won't work, he hard wired each of the door locks. Only the passenger door locks seem to work. Anyone have thoughts as to why?

escalade007 
Member - Posts: 6
Member spacespace
Joined: June 20, 2006
Posted: June 23, 2006 at 10:23 PM / IP Logged  
Problem solved.. only have to wait for a module for kill/starter to come out.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, April 18, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer