2005 Grand Cherokee problems

Home / the12volt's Install Bay / Car Security and Convenience / 2005 Grand Cherokee problems (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

azn_fcuk

Copper - Posts: 104

Joined: November 09, 2005

Location: Canada

Posted: November 14, 2006 at 11:13 PM / IP Logged

I just installed a compustar 2way starter only into this beautiful truck. Now when i remotley start the vehicle the Traction Control light stays on, and the on board computer reads "problem with electronic brake" when i start with key im fine.

Ive checked all my resistence's and their bang on. Also I wirred my 2nd starter and Accessory just like this http://64.85.6.129/extrainfo/diagrams/26500_GRAND-CHEROKEE_CHRYSLERS%20STARTER%202%20AND%20ACCESSORY%20DIAGRAM.pdf

Now i used universal bypass for transponder and a CAN SL for my anti theft and accessorys.

Im also getting positvie feed back into my Ground in while Running wire, Door locks, and Trunk release. I diode isolated my Ground in while running wire and my 2nd starter wire.

IM SO CONFUSED

tha

azn_fcuk

Copper - Posts: 104

Joined: November 09, 2005

Location: Canada

Posted: November 15, 2006 at 11:51 AM / IP Logged

any takers

Hymer

Silver - Posts: 695

Joined: November 20, 2004

Location: United States

Posted: November 15, 2006 at 1:36 PM / IP Logged

Where are you pullung your main 12v supply from.... if it's from lt blu and red it could be causing a problem.. ran into that before.. Pull your main power directly from tha battery... personally I would go with the bypass that takes care of all the chrysler bs with resistors and second starter outputs and such... It works great.. saves a lot of headaches

Tire Proz Stillwater Mn

High End Restyling and Comlete Repair

azn_fcuk

Copper - Posts: 104

Joined: November 09, 2005

Location: Canada

Posted: November 15, 2006 at 2:28 PM / IP Logged

I went right to the battery.

I used the CanSL which takes care of all features like door locks and such, which is why i cant figaure out where the feed back is comming from

damn

kgerry

Platinum - Posts: 3,455

This member consistently provides reliable information

Joined: February 07, 2004

Location: Saskatchewan, Canada

Posted: November 15, 2006 at 3:00 PM / IP Logged

sounds like you may have missing powering an extra ign or acc wire... which did you power?

Kevin Gerry

Certified Electronics Technician

MECP First Class Installer

Owner/Installer

Classic Car Audio

since 1979

azn_fcuk

Copper - Posts: 104

Joined: November 09, 2005

Location: Canada

Posted: November 15, 2006 at 4:00 PM / IP Logged

I powerd ign, acc is relayed with resistor, the same with 2nd starter.

hmmm

kgerry

Platinum - Posts: 3,455

Joined: February 07, 2004

Location: Saskatchewan, Canada

Posted: November 15, 2006 at 4:58 PM / IP Logged

should be ok then... i always use a PKU-CH2GX and dont bother with the relays and resistors and i havent had any issues....

Kevin Gerry

Certified Electronics Technician

MECP First Class Installer

Owner/Installer

Classic Car Audio

since 1979

azn_fcuk

Copper - Posts: 104

Joined: November 09, 2005

Location: Canada

Posted: November 15, 2006 at 5:17 PM / IP Logged

the 2nd starter and acc are negative on the data wire right? it does need a relay.

or are you saying that bypass will accomodate for neg 2nd starter and acc with the probper resistance?

Hymer

Silver - Posts: 695

Joined: November 20, 2004

Location: United States

Posted: November 15, 2006 at 5:20 PM / IP Logged

no resistors are needed with the bypass... 2nd start or accy

Tire Proz Stillwater Mn

High End Restyling and Comlete Repair

kgerry

Platinum - Posts: 3,455

Joined: February 07, 2004

Location: Saskatchewan, Canada

Posted: November 15, 2006 at 5:25 PM / IP Logged

PKU-CH2GX allows for 2nd start and 2nd acc with built in resistors,,,, bypasses 1st and 2nd gen Sentry key...also disarms oem alarm.... sweet little module....

Kevin Gerry

Certified Electronics Technician

MECP First Class Installer

Owner/Installer

Classic Car Audio

since 1979

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.