01 town and country RS

This is the diagram I followed for the last 01 T&C I did, worked flawlessly: DIRECTWIRE™ WIRING INFORMATION - CHRYSLER / TOWN AND COUNTRY / 2001 / Remote Start [PRINT THIS PAGE] 12volts      lt. blue/red (10A)       +       ignition harness Notes: This wire is rated at 10 amps only. If installing any system with high current outputs, go to battery for 12v. Starter      yellow       +       ignition harness Second Starter      PURPLE / brown       -       ignition harness Notes: The second starter wire is negative trigger thru a 180 ohm resistor. MUST use relay. Refer to DirectFax document 1083 for wiring information. Ignition      pink/white       +       ignition harness Second Ignition      N/A               Third Ignition      N/A               Accessory      not required for remote start               Second Accessory      N/A               Keysense                     Power Lock      PURPLE / green       -       conn. 3, pin 21 @ BCM Notes: Lock is negative trigger thru a 5.3K ohm resistor. Unlock is negative trigger thru a 2.0K ohm resistor. MUST use relays. The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs. Can also use Directed interface modules. Power Unlock      same wire as power lock               Lock Motor      tan/white              conn. 2, pin 10 @ BCM Notes: The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs. Unlock Motor      tan/lt. green              conn. 2, pin 28 @ BCM Notes: The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs. Parking Lights+      DO NOT USE               Parking Lights-      WHITE/ brown       -       headlight switch Notes: The parking lights are negative trigger thru a 2.1K ohm resistor. The headlights are negative trigger thru a 790 ohm resistor. There is a rest resistance on the wire, so MUST use a relay to isolate away from the switch. See DirectFax document 1082 for wiring information. Hazards                     Turn Signal(L)                     Turn Signal(R)                     Reverse Light                     Door Trigger             -       conn. 3 @ BCM Notes: There are separate door triggers for each door, they are all in connector 3 at the BCM. The driver door trigger is purple in pin 6, the passenger door is PURPLE / white in pin 7, the left sliding door is PURPLE / gray in pin 8, and the right sliding door is purple / YELLOW in pin 5. Use all four and diode isolate each. See DirectFax document 1076 for wiring information. The BCM is in the drivers kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs. Dome Supervision      use door trigger               Trunk/Hatch Pin      PURPLE / orange       -       conn. 3, pin 29 @ BCM Notes: A diode must be placed inline on this wire to avoid problems with the dome lights and parking lights. The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs. Hood Pin      PURPLE / lt. blue       -       conn. 3, pin 30 @ BCM Notes: The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs. Trunk/Hatch Release      PURPLE / tan       -       conn. 2, pin 6 @ BCM Notes: Hatch release is negative trigger thru a 1.69K ohm resistor. MUST use a relay. The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs. Power Sliding Door      PURPLE / blue       -       conn. 3, pin 1 @ BCM Notes: Left power sliding door is negative trigger thru a 1.5K ohm resistor. Right power sliding door is negative trigger thru a 2.7K ohm resistor. MUST use relays. The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs. Factory Alarm Arm      PURPLE / lt. blue       -       conn. 3, pin 14 @ BCM Notes: Arm is negative trigger thru a 1.5K ohm resistor, this will also lock the doors. Disarm is negative trigger thru a 9.1K ohm resistor, if use double pulse this will also unlock the doors. MUST use relays. The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs. Can also use Directed interface modules. Factory Alarm Disarm      same wire alarm arm               Disarm No Unlock                     Tachometer             ac       ignition coil pack Notes: On the 2.4L use blue/green or blue/tan. On the 3.3L/3.8L use blue/green, blue/tan or blue/orange. Wait to start                     Notes: test Brake Wire      WHITE/ tan       +       brake pedal switch Parking Brake                     Horn Trigger      GREEN/ purple       -       steering column Memory Seat 1                     Memory Seat 2                     Memory Seat 3                     Interface Module:      Category: Immobilizer Bypass      Required: Yes      Type: Sentry Key Part #: 555CW Alternate Part1 #: 556UW Alternate Part2 #: DesignTech 20402 Alternate Part3 #: DesignTech 29402 Notes: Only vehicles with gray keys have the immobilizer. Interface Module:      Category: Door Lock Interface      Required: No      Type: Data Bus Part #: 457CW Alternate Part1 #: 456LW Notes: Smart Starter Kill Relays: Not Available warning       This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter. Directed Electronics assumes no responsibility with regards to the accuracy or currency of this information. Proper installation in every case is and remains the responsibility of the installer. DEI assumes no liability or responsibility resulting from improper installation, even in reliance upon this information. Here is document 1083.

I am using this as my second start wire with the resistor and the engine is still just cranking. No imoblizer on this vehicle as it has the black key. What will make this car start? 2000 caravan with 2001 wiring 8/00 manufacture date.