the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

remote start, 2007 jeep compass


Post ReplyPost New Topic
< Prev Topic Next Topic >
papichullo75 
Member - Posts: 14
Member spacespace
Joined: December 09, 2007
Location: New Jersey, United States
Posted: December 09, 2007 at 9:16 PM / IP Logged  
Has anyone done a remote start in a 2007 Jeep Compass!!!!!  I am installing a viper 160rs and using the XK532 bypass.  
papichullo75 
Member - Posts: 14
Member spacespace
Joined: December 09, 2007
Location: New Jersey, United States
Posted: December 11, 2007 at 3:35 PM / IP Logged  
I need your help guys!!!! I had a 2007 Jeep Compass at the shop for a remote start. Now I am installing a viper 160 remote start with the xk532 bypass. Now get this I wired up the remote start and the xk532 box( looked like a easy car to do) First I programed the tach for the viper 160rs(done) then I programed the xk532 box for key code(done) then I gave the xk532 box power , the xk532 found the door locks perfect, the I remote started the car and it work PERFECT!!!! The I hit the brake to shut the system down. Tried to remote start it again the car would not crank. Now I tired to put the 1000 ohm resistor in with the pink output from the xk532 box to ground and the same thing. I am almost sure it has something to do with the mux wire. Please any info the you guys can give me I appreciation!!!!!
chriswallace187 
Gold - Posts: 1,661
Gold spacespace
Joined: March 11, 2002
Location: Pennsylvania, United States
Posted: December 11, 2007 at 4:18 PM / IP Logged  
Read this post - basically the same bypass situation.
C Renner's Auto Electronix
My service is cheap, quick, and good - pick any two
mobilefx 
Copper - Posts: 48
Copper spacespace
Joined: November 05, 2003
Location: United States
Posted: December 11, 2007 at 10:28 PM / IP Logged  

i had 100% same install issue w/ the xk530 module i think it was.  car was a 06 pt cruiser.   done in about an hr and started up first try like a champ.  doorlocks also never failed.  tried to restart and same crap.. not crankin.    my heater was workin so i new the acc portion of the mux output was good and proper.  i ended up doin a separate relay to create the neg 180 ohms 2nd start and sent it to the purp/brown mux.  i still needed to use the start input to the bypass module so that the acc portion of the mux would function properly.  

worked fine but the troubleshoot sucked and i tried 3 modules, 2 of which were different.     they all did the same thing and they all didn't program properly as far as l.e.d was concerned.     all did doors/sec  without even programin and worked fine. 

hope that helps.. sounds exaclty the same tho.  why would the dam thing work on first start every time..  i would reset modueles and they workd one time.   

done any 08 town and country vans w/ trilogix mods.. i have one tomoro.  

mobile f/x
papichullo75 
Member - Posts: 14
Member spacespace
Joined: December 09, 2007
Location: New Jersey, United States
Posted: December 12, 2007 at 8:08 AM / IP Logged  
Thanks Guys!!! I have the car back at the shop on sunday, so I will try so new things out. I think the best way so far is using the xk532 box for the door locks and bypass, and just use to relays for the mux wire(directed tip 1084) ON SUNDAY I WILL WIN OVER THIS CAR!!!! LOL
chriswallace187 
Gold - Posts: 1,661
Gold spacespace
Joined: March 11, 2002
Location: Pennsylvania, United States
Posted: December 12, 2007 at 5:21 PM / IP Logged  
The XK532 should take care of the MUX wire with no problem - as long as the (+) ignition and (+) start wires to it are hooked up properly.
If you are using an accessory output it will probably not work right because it drops out during crank. If this car doesn't have a conventional (+) starter wire at the ignition switch, you definitely need to put the 1000 ohm resistor to ground on that wire like the XK532's instructions say to do.
Also I would recommend connecting the XK532's ignition input to your primary ignition circuit(i.e. don't hook it to the 2nd ignition from the remote start where it's not connected directly to the car.)
C Renner's Auto Electronix
My service is cheap, quick, and good - pick any two
papichullo75 
Member - Posts: 14
Member spacespace
Joined: December 09, 2007
Location: New Jersey, United States
Posted: December 13, 2007 at 6:22 AM / IP Logged  

Ok the way I had the xk532 box wired up:

Brown- 3 ignition wire (-) for the Viper 160

Green- Lock

Blue- Unlock

Violet/White- PURPLE / Brown (mux wire) in the car

Violet- WHITE/ Orange wire off the skim module in car

Pink/white- NC

Pink- Purple (+) wire off the viper 160 (Yes I have the 1000 ohm resistor going to ground too)

Orange- NC

Red- 12 volt constant

Black- Chassis Ground

Is this right????

The Only wire that I am using off the viper 160 is:

Off the Heavy Gauge Relay Box:

All three high current 12v input wires- Going to 10g wire from battery

Green key side starter input- nc

Purple starter side output: Going to the Pink wire on the xk532 bow with a 1000 ohm resistor going to ground

Pink wire- going to the ignition wire in car

Pink/white-nc

Orange-nc

chriswallace187 
Gold - Posts: 1,661
Gold spacespace
Joined: March 11, 2002
Location: Pennsylvania, United States
Posted: December 14, 2007 at 8:18 AM / IP Logged  
That sounds all good...the only thing that might be trouble is if the ignition 3 comes on before the primary ignition, but I don't think that's an issue on a Directed remote start since they've got the status output wire separate from ignition 3.
C Renner's Auto Electronix
My service is cheap, quick, and good - pick any two
papichullo75 
Member - Posts: 14
Member spacespace
Joined: December 09, 2007
Location: New Jersey, United States
Posted: December 14, 2007 at 8:32 PM / IP Logged  

Hey Chriswallace187 did you do a 07 Jeep Compass?

moonliter 
Copper - Posts: 322
Copper spacespace
Joined: February 28, 2007
Location: Canada
Posted: December 14, 2007 at 8:55 PM / IP Logged  
Had u cycle the lock & unlock on ur fac remote ? Also not to overlook the loop u wrapped around the key cylinder. Make sure it hadn't moved or shifted. U can also check to see whether it was the transponder's problem by placing the head of key close to the ignition barrel ( with the connector for the loop disconnected ) , remote start it and see what would happen.
Page of 2

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Friday, March 29, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer