toyota power windows

Home / the12volt's Install Bay / Relays / toyota power windows (

Topic Closed)

Welcome Guest :)

Members

Search

Register

Login

< Prev Topic Next Topic >

berhntr

Member - Posts: 2

Joined: January 12, 2010

Posted: January 12, 2010 at 9:24 PM / IP Logged

I am new here. I am trying to add power windows to my 85 toyota pickup. I got some factory switches out of a 4runner that i want to use. the switch has a common in the center of the rocker and then a leg on either side that is switched accordingly. the motors i got are reverse polarity, can anyone tell me how to wire this up? i am clueless when it comes to relays.

Back to Top

berhntr

Member - Posts: 2

Joined: January 12, 2010

Posted: January 13, 2010 at 3:48 PM / IP Logged

Do i not have enough information listed or what?

Back to Top

t&t tech

Platinum - Posts: 2,608

Joined: October 05, 2008

Location: Trinidad and Tobago

Posted: January 13, 2010 at 7:32 PM / IP Logged

commit your way to jehovah and he will act in your behalf. psalms 37:5

Back to Top

t&t tech

Platinum - Posts: 2,608

Joined: October 05, 2008

Location: Trinidad and Tobago

Posted: January 13, 2010 at 7:37 PM / IP Logged

The leads labelled actuators will go to the motor wires! Pin 87 on both relays to a fused proper twelve volt source at say ten amps! The pins labelled alarm lock and alarm unlock output will be connected to the switch the centre pin goes to ground! Pins 86 and 85 on the inside of the relays that are connected to the constant in the diagram can be connected to an ignition feed, so that it only powers on ignition! That setup would be per door!

commit your way to jehovah and he will act in your behalf. psalms 37:5

Back to Top

utopialand

Member - Posts: 1

Joined: January 07, 2004

Location: United States

Posted: September 30, 2010 at 8:56 PM / IP Logged

t&t tech wrote:

would this be the same way for a 2008 tocoma for remote windows on stock alarm

Back to Top

t&t tech

Platinum - Posts: 2,608

Joined: October 05, 2008

Location: Trinidad and Tobago

Posted: October 01, 2010 at 8:46 PM / IP Logged

Remote windows? Do you mean u want to have them roll via the alarm? Or do u want to convert them to powered from a manual state?

Back to Top

howie ll

Pot Metal - Posts: 16,466

Joined: January 09, 2007

Location: United Kingdom

Posted: October 02, 2010 at 9:12 AM / IP Logged

No since you only have 3 terminal switches rather than the correct 5 or 6 with illumination switches you would need the relays to make the motors work. Auto close would go to the close side relay at 86 assuming constant 12V+ in that diagramme. The original Toyota wiring would have included the relays somewhere.

Back to Top

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

toyota power windows

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.