98 mitsu eclipse

Home / the12volt's Install Bay / Vehicle Wiring Information & File Requests / 98 mitsu eclipse (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

Edtfun

Member - Posts: 6

Joined: May 13, 2002

Location: United States

Posted: May 13, 2002 at 2:13 PM / IP Logged

I am trying to install a remote starter into my eclipse.

I need help bad, i have no wiring diagrams and the instruction that they provide are not very good at all. i need informatoin on how to proform this install.

edtfun

wirewise

Moderator - Posts: 489

This member has made a donation to the12volt.com. Click here for more info.

This member consistently provides reliable information

Joined: March 07, 2002

Location: California, United States

Posted: May 13, 2002 at 2:22 PM / IP Logged

Hey EDTFUN, what specific information or parts of the install do you need help with?

For the wiring info for your vehicle look here: https://www.the12volt.com/installbay/detail.asp?info=alarm&year=1998&make=Mitsubishi&model=Eclipse&ID=18460&type=Alarm

~wirewise~ Verify all wiring with your meter before making any connections!

Big Dog

Gold - Posts: 1,265

Joined: May 02, 2002

Location: Quebec, Canada

Posted: May 13, 2002 at 2:55 PM / IP Logged

Hey EDTFUN,

What brand and model is your starter? Is your Mtsu a manual?

Prepare your future. It wasn't the lack of stones that killed the stone age.

Edtfun

Member - Posts: 6

Joined: May 13, 2002

Location: United States

Posted: May 14, 2002 at 11:50 AM / IP Logged

IT IS AN ULTRASTARTER 1250M. I AM JUST LOOKING FOR THE TACH WIRE NOW. I STARTED WORKING ON THE INSTALL LAST NIGHT, BUT WAS UNABLE TO FINISH. YES MY MITSU IS A MANUAL.

P.S. PLEASE DON'T MIND THE CAPS.

edtfun

Edtfun

Member - Posts: 6

Joined: May 13, 2002

Location: United States

Posted: May 15, 2002 at 7:05 AM / IP Logged

Can I find a tach signal inside the car, because I can't find a hole in the fire wall to run a line to the engine compartment. Other than that I think that every thing else is O.K. I also need to know weather or not i need to use the hood pin.

edtfun

Velocity Motors

Moderator - Posts: 12,488

This member has been recognized as an authority in Electrical Theory. Click here for more info.

This member has been recognized as an authority in Fabrication. Click here for more info.

This member has been recognized as an authority in Mobile Audio and Video. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: May 15, 2002 at 8:36 PM / IP Logged

Tach Signal:		WHITE OR BLUE/RED	PIN 8 AT ENGINE CONTROL MODULE *
Parking Lights:		GREEN / WHITE	(+) FUSE/JUNCTION BLOCK OR DIMMER
Headlights:		RED	(-) AT HEADLIGHT SWITCH OR RELAY
OEM Alarm Disarm:		GREEN / WHITE	(-) DRIVER KICK PANEL
OEM Alarm Arm:		GREEN/ YELLOW	(-) DRIVER KICK PANEL


Notes:	* Engine Control Module (ECM) Located On Driver Wheelwell. WHITE Tach Wire Is Also Located At Pin #6 In A White 18 Pin Connector Behind Driver Side Of Console.

try this and see if this will help you out.

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Search for other posts by Velocity Motors

Edtfun

Member - Posts: 6

Joined: May 13, 2002

Location: United States

Posted: May 18, 2002 at 7:29 AM / IP Logged

O.K. evey thing is on and working, there is one problem. The remote starter will not start unless

I hold the clutch in. The installation guide says that as long as the remote starter is set for reservation mode, that it should start. By pushing in the brakes, and pulling the parking brake, when I turn the key off, and take it out the car still is running. When I exit the car, and close the door the car shuts off, and is in reservation mode. According to this installation guide, this process is the temporary clutch bypass.

I need to know how to get the car to remote start with out me in the car. 98 mitsu eclipse -- posted image.

edtfun

the12volt

Administrator - Posts: 3,955

Joined: March 07, 2002

Location: Louisiana, United States

Posted: May 18, 2002 at 7:42 AM / IP Logged

Hi Edtfun, first thing that comes to mind...did you wire it to bypass the clutch? I realize it has the capability to bypass the clutch, but if you didn't wire it, you'll need to add a relay to close the two leads on the clutch switch during remote start.

the12volt

Edtfun

Member - Posts: 6

Joined: May 13, 2002

Location: United States

Posted: May 18, 2002 at 1:42 PM / IP Logged

Thanks for the advice the12volt, but how do i go about wiring the relay.

edtfun

Edtfun

Member - Posts: 6

Joined: May 13, 2002

Location: United States

Posted: May 20, 2002 at 8:42 AM / IP Logged

Where can i find the clutch switch.

please help.

edtfun

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.