99 Chrysler concorde

Home / the12volt's Install Bay / Vehicle Wiring Information & File Requests / 99 Chrysler concorde (

Topic Closed)

Welcome Guest :)

Members

Search

Register

Login

< Prev Topic Next Topic >

therealist

Member - Posts: 5

Joined: July 08, 2005

Posted: August 19, 2006 at 10:12 AM / IP Logged

anyone have specific wiring locations and colors for this car.I'm installing an alarm with keyless entry,remote start and all the other basics

Back to Top

josh1979

Silver - Posts: 320

Joined: July 03, 2006

Location: United States

Posted: August 19, 2006 at 9:06 PM / IP Logged

CHRYSLER / CONCORDE / 1999 / Remote Start

12volts	pink/black or red	+	ignition harness
Starter	yellow	+	ignition harness
Second Starter
Ignition	dk. blue/white	+	ignition harness
Second Ignition	GREEN/ red	+	ignition harness
Third Ignition
Accessory	BLACK/ orange	+	ignition harness
Second Accessory	BLACK/ white	+	ignition harness
Keysense
Power Lock	WHITE/ green	+	back of fusebox
Notes: Locks are positive trigger through resistors. Use 2.7K (2700) ohms for lock and 620 ohms for unlock.
Power Unlock	same wire
Lock Motor	orange		BCM
Notes: BCM is located on the left side of dash with junction block.
Unlock Motor	dk. blue		BCM
Notes: BCM is located on the left side of dash with junction block.
Parking Lights+	BLACK / YELLOW	+	driver kick panel
Parking Lights-	yellow		headlight switch
Notes: Use a 110 ohm resistor to ground (-) for parking lights and a 220 ohm resistor to ground (-) will do both headlights and parking lights.
Hazards
Turn Signal(L)
Turn Signal(R)
Reverse Light
Door Trigger	tan and tan/red	-	BCM
Notes: BCM is located on the left side of dash with junction block.
Dome Supervision	yellow	-	rear of fuse box, brown plug
Trunk/Hatch Pin	tan/black	-	drivers kick panel
Hood Pin
Trunk/Hatch Release	BLACK/ white	+	at release switch
Power Sliding Door
Factory Alarm Arm	lt. GREEN/ orange	+	drivers kick panel
Notes: Arm is positive trigger thru a 1.87K ohm resistor, this will also lock the doors. Disarm is positive trigger thru a 680 ohm resistor, if use double pulse this will also unlock the doors. Must use relays.
Factory Alarm Disarm	same wire
Disarm No Unlock
Tachometer			one of the coils
Notes: This vehicle has an ignition coil for each cylinder. For tach use a tan/stripe wire at any one of the coils.
Wait to start
Brake Wire	WHITE/ tan	+	at brake switch
Parking Brake
Horn Trigger	BLACK/ red	-	steering column
Memory Seat 1
Memory Seat 2
Memory Seat 3

Interface Module:	Category: Immobilizer Bypass	Required: Yes	Type: Sentry Key
Part #: 555CW
Alternate Part1 #: 556UW
Alternate Part2 #: DesignTech 20402
Alternate Part3 #: DesignTech 29402
Notes: Only vehicles with gray keys have the immobilizer.
Interface Module:	Category: Door Lock Interface	Required: Yes	Type: Multiplex
Part #: 456LW
Notes:

bring back the rotary phone so i dont have to press 1 to proceed in english

Back to Top

therealist

Member - Posts: 5

Joined: July 08, 2005

Posted: August 22, 2006 at 7:35 PM / IP Logged

Thanks alot this will be very helpful

Back to Top

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

99 Chrysler concorde

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.