Hello Everyone, I have the Ungo KE106 keyless entry device diagram but not the wiring diagram for the 2001 Stratus. Can anyone help? Thanks in advance!
-------------
Capt. AL
THIS IS FOR THE 4 door.
- | 12V|pink/black & red |+ |ignition harness |
| STARTER|yellow |+ |ignition harness |
| IGNITION|blue |+ |ignition harness |
| SECOND IGNITION|GREEN/ red (20awg) |+ |ignition harness |
| ACCESSORY|BLACK/ orange |+ |ignition harness |
| SECOND ACCESSORY|BLACK/ white |+ |ignition harness |
| POWER LOCK|WHITE/ green |*1 |conn. C4, pin 15 @ BCM *2 |
| POWER UNLOCK|same |*1 |same |
| LOCK MOTOR|ORANGE / black | |conn. C4, pin 9 @ BCM *2 |
| UNLOCK MOTOR|blue/white | |conn. C4, pin 13 @ BCM *2 |
| DISARM DEFEAT|pink/lt. blue | |conn. C4, pin 25 @ BCM *2 |
| PARKING LIGHTS +|BLACK / YELLOW | |headlight switch or DKP |
| HEADLIGHTS|PURPLE / white |+ |headlight switch |
| DOOR TRIGGER|*3 |- |BCM *2 |
| DOME SUPERVISION|use door trigger | | |
| TRUNK/HATCH PIN|tan/black |- |conn. C4, pin 18 @ BCM *2 |
|TRNK/HTCH RELEASE|BLACK/ white |5wi|conn. C4, pin 1 @ BCM *2 |
| FCTRY ALARM ARM|lt. GREEN/ orange |*4 |conn. C4, pin 4 @ BCM *2 |
|FCTRY ALRM DISARM|same |*4 |same |
| TACHOMETER|*5 | |*5 |
| SPEED SENSE|WHITE/ orange |8 |conn. C2, pin 66 @ PCM *6 |
| BRAKE WIRE|WHITE/ tan |+ |brake pedal switch |
| HORN TRIGGER|BLACK/ red |- |steering column |
| WIPERS|brn/wht, RED / yel |+ |wiper motor |
| LF WINDOW UP/DN|lt. blue - white |A |drivers window switch |
| RF WINDOW UP/DN|brn/wht - pur/wht |A |drivers kick panel |
| LR WINDOW UP/DN|blu/wht - RED / blk |A |drivers kick panel |
| RR WINDOW UP/DN|gry/blk - grn/wht |A |drivers kick panel |
| SUN RF OPN/CLOSE|not recommended | | |
| RADIO 12V|pink |+ |radio |
| RADIO GROUND| | | |
| RADIO SWITCH|RED / white |+ |radio |
| RADIO ILLUMINATE|ORANGE / brown |+ |radio |
| LF SPEAKER|green - brn/red | |radio |
| RF SPEAKER|purple - blu/red | |radio |
| LR SPEAKER|brn/yel - brn/lt blu| |radio |
| RR SPEAKER|blu/wht - blu/org | |radio |
Notes:
NOTE: Chrysler vehicles that use a gray ignition key have an immobilizer system that needs to be bypassed when remote starting. *1 Lock is positive thru a 1800 ohm resistor, unlock is positive thru a 750 ohm resistor. Must use relays. *2 The BCM is attached to the fuse/relay box at the end of the dash on the driver side. Connector C4 is a 26 pin plug on the bottom edge of the BCM. *3 All the door triggers are in connector C4 at the BCM. The drivers door trigger is tan in pin 5, the front passenger door is tan/red in pin 6, the left rear door is tan/orange in pin 7, and the right rear door is tan / YELLOW in pin 8. Use all four and diode isolate each. *4 Arm is positive trigger thru a 1800 ohm resistor, disarm is positive thru a 750 ohm resistor. Must use relays. *5 For tach go to either a coil or an injector and use the wire that is NOT GREEN/ lt. green. *6 The PCM is between the air filter box and the power distribution box on the driver side of the engine compartment.
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Thanks for the awsome quick reply!
But I'm Sorry I didn't mention the model type.
Yes, I do need the four door model SE stratus Diagram.
Also the ungo KE106 has an "Orange: Optional Circuit Default (-) output [500mA]" What is this wire for?
Thank You in advance for your reply!
-------------
Capt. AL
The KE 106 is a hard system to figure out, but it works great once you get it all installed.
-------------
werd