SUB BREAK-IN PERIOD

Hey all

I just replaced my 3 10" 8000 series MTX with 3 new ones and was wondering how long they usually take to break-in. I bought the last set 3 months, used from a friend, and they hit extremely hard compared to these new ones. The box is sealed and airtight, and the subs have a good bead of silicone applied.

Exact same sub only these are new.

The just aren't hitting hard or holding the long hits.

I use a 150 amp alt and an SP1700 battery. 14.4 volts always.

Anyone????

-------------
BOOM, BOOM, BOOM BOOM....

Break in period is 20 hours playing at low volume.

Well, I definitely didn't do that. What happens if tghey are not broken in properly?

-------------
BOOM, BOOM, BOOM BOOM....

Is that 20hours at low volume for all subs in general?

-------------
BOOM, BOOM, BOOM BOOM....

Ya thats just a general rule of thumb. Give it a week or two and see if the sound improves

-------------
double-secret reverse-osmosis speaker-cone-induced high-level interference distortion, Its a killer

The only difference is in the settings after the sub has broken in and become more flexible.  Readjust the gain, crossover and anything else you can think of to tinker with.  It's pretty normal (for a DIY install) to do a system tweak a few times anyway.  The hardest part is to keep yourself from blasting a new sub to full power, right out of the box.  When setting gain on the amp by ear, that's exactly what you have to do.  That's why a recheck of gain setting is in order after a week.  If you're setting gain with a DMM, you can do that with the sub unhooked and save the trauma to the new speaker...and get a more accurate setting.

-------------
Build the box so that it performs well in the worst case scenario and, in return, it will reward you at all times.

(If you're setting gain with a DMM, you can do that with the sub unhooked and save the trauma to the new speaker...and get a more accurate setting.)

Is that DMM a digital multimeter? How would I use it to check gain? That sounds like a great idea.

-------------
BOOM, BOOM, BOOM BOOM....

<Break in period is 20 hours playing at low volume.>

I played them pretty hard, especially while setting gain. Do you think that could have already damaged them? 

-------------
BOOM, BOOM, BOOM BOOM....

No, you wouldn't have damaged them doing that.  Playing them hard at clipping level will do the damage.  You just might not have gotten an accurate enough "measurement by ear" because setting gain is listening for distortion, and you might not hear it as well with a new sub.  As far as DMM = digital multimeter, yes.  Read AC volts at the speaker terminals of the amp, with sub unhooked, HU at max clean volume, crossover at full, bass boost off...you will be reading the voltage that you have figured using Ohm's Law as it applies to the power you want to send to the speaker(s) at the ohm resistance on the amp.

A test tone is necessary, played through the CD unit.  You can use 50 Hz for subs, or get the highest reading by trying several freqs in the sub's range.  You can't get a steady or accurate reading by playing music.

E=(PXR)^.5  which is to say:  voltage in AC volts = the square root of (watts of power times the ohm resistance).  You can post your particulars here for some verification of numbers if you want.

Then having set the gain with the meter, you won't have to rely on  hearing distortion at full volume, which can be very difficult to do.  A new sub then can be played at reasonable levels for several hours before show-off time starts.

-------------
Build the box so that it performs well in the worst case scenario and, in return, it will reward you at all times.

Excellent! I learned something new today :)

-------------
BOOM, BOOM, BOOM BOOM....

Cool, I learned it through this forum, too, so I'm happy to pass on what I've learned and tried.  Post up how everything went when you do it.  There's some links to test tones too; searching through the posts should net you a couple.  Let me know if you want to make a test tone CD and I'll share what I've found on that.

-------------
Build the box so that it performs well in the worst case scenario and, in return, it will reward you at all times.

The 8000's are starting to sound better. I think they are suffering from a poor enclosure. It is airtight, screwed, braced, and glued, but it's made out of 1/2" and It's volume is a little small for 3 10" 8000's. Maybe instead of replacing the 3 10's for the 2 9500's right now, I'll just buy a new subzero 3-10 box and try it out. That'll only be about 210$

-------------
BOOM, BOOM, BOOM BOOM....