what do you think about this amp
Printed From: the12volt.com
Forum Name: Car Audio
Forum Discription: Car Stereos, Amplifiers, Crossovers, Processors, Speakers, Subwoofers, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=99021
Printed Date: May 11, 2025 at 4:09 PM
Topic: what do you think about this amp
Posted By: spedfix
Subject: what do you think about this amp
Date Posted: November 14, 2007 at 10:56 PM
| Specifications: *Power output: 125 watts RMS x 2 (4 ohm load), 200 watts RMS x 2 (2 ohm load), 800 watts max x 2 (4 ohm load) *Total Harmonic Distortion (THD): 0.04% *Signal to Noise ratio (S/N): 95 dB *Input sensitivity: 250 mV-2.5 V *Frequency response: 15-30,000 Hz *Dimensions: 15"L 11-1/3"W 2-1/4"H *Two-year manufacturer's warranty. | - Remote bass level control
- Electronic crossover network (low / full / high)
- Bass boost circuit
- MOSFET PWM Power Supply
- High and low level inputs
- 2-ohm stable
- Power and protection LED indicators
- Soft turn-on circuit
|
the price is 109.00 $ I will be using this for 2 750 watt swiss audio 12"(each at 4ohm's) let me know you think
Replies:
Posted By: jmelton86
Date Posted: November 14, 2007 at 11:14 PM
With 2 4ohm subs, you'll only be able to get about 125Wrms x 2 from the amp -125Watts to each sub. What is the brand? Or, what size fuse(s) does it have in it? ------------- 2013 Kia Rio -90a alternator
DDX470HD GTO14001 GTO1014D (x3)
Big3 in 1/0G
1/0G to GTO14001
Posted By: spedfix
Date Posted: November 14, 2007 at 11:39 PM
pyle Yeah was lookign at the wrong rating don't see a fuse size I am looking at this one too Pyle PLA2840 2x4000W Amplifier | Specifications: *Power output: 300 watts RMS x 2 (4 ohm load), 450 watts RMS x 2 (2 ohm load), 2000 watts max x 2 (4 ohm load) *Total Harmonic Distortion (THD): 0.04% *Signal to Noise ratio (S/N): 95 dB *Input sensitivity: 250 mV-2.5 V *Frequency response: 15-30,000 Hz *Dimensions: 21"L 11-1/3"W 2-1/4"H *Two-year manufacturer's warranty. | - Remote bass level control
- Electronic crossover network (low / full / high)
- Bass boost circuit
- MOSFET PWM power supply
- High and low level inputs
- 2-ohm stable
- Power and protection LED indicators
- Soft turn-on circuit
my speaker are 350 rms 750peak this should work good right |
Posted By: spedfix
Date Posted: November 14, 2007 at 11:43 PM
the above seems to pretty good price wise @ 189.50 to what do you guy think
Posted By: dwarren
Date Posted: November 14, 2007 at 11:45 PM
I would avoid Pyle like the plague. I can totally understand some one who is on a budget or simply does not want to spend an arm and a leg on equipment, but brands like this are not worth any amount of your money. Perhaps you are limited by your budget, but for not a whole lot more you may be able to get some thing worth while, that will actually perform! -------------
Posted By: jmelton86
Date Posted: November 14, 2007 at 11:46 PM
You already have the 2 (4ohm, 350Watts RMS) subs? What is your spending limit? Pyle is not that great, at all. You're better off getting a CEA-compliant amp that is rated for half the power then what the Pyle claims. ------------- 2013 Kia Rio -90a alternator
DDX470HD GTO14001 GTO1014D (x3)
Big3 in 1/0G
1/0G to GTO14001
Posted By: jmelton86
Date Posted: November 14, 2007 at 11:47 PM
Also, for the money you're better off getting a mono amp stable @ 2ohms.
-------------
2013 Kia Rio -90a alternator
DDX470HD GTO14001 GTO1014D (x3)
Big3 in 1/0G
1/0G to GTO14001
Posted By: tcss
Date Posted: November 15, 2007 at 12:01 AM
If that's your max budget, get a used name brand amp on Flea-Bay.
-------------
There is no such thing as free installation!
Posted By: coppellstereo
Date Posted: November 15, 2007 at 9:56 AM
I havent compared prices in a while, but I used to buy stuff from www.ikesound.com
Posted By: aznboi3644
Date Posted: November 15, 2007 at 5:04 PM
pyle sucks....the output is nowhere even near those ratings..
300 watts rms x 2 channels at 4 ohm load...more like 50-100 weak sauce watts
|