Integra Enclosure Pics
Printed From: the12volt.com
Forum Name: Rides and Systems Gallery
Forum Discription: Show off your vehicles, systems, and installations.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=59280
Printed Date: April 25, 2024 at 10:15 PM
Topic: Integra Enclosure Pics
Posted By: Tegpilot
Subject: Integra Enclosure Pics
Date Posted: July 12, 2005 at 10:31 AM
   I took out the side trunk liner and as you can see put down foil and duct tape for the rear of the mold  this is the first layer of glass  fleece stretched  ring after trimming edge of mold
Replies:
Posted By: Poormanq45
Date Posted: July 12, 2005 at 12:00 PM
It looks very good so far.
Question though: Why did you cut the mold back so far? Do you want ti to stick out that much?
I guess it's just personal opinion, but I like to have the ring stick out only a little bit so that it almost looks flush mounted. This gives you a bit more airspace too.
ANyways, it looks GREAT!
-------------
Posted By: One_Dieu
Date Posted: July 12, 2005 at 3:34 PM
What kind of sub is that?
-------------
Respect the Blood Line
Posted By: abovestock
Date Posted: July 12, 2005 at 5:52 PM
That looks sweet. I love the shape of the box it is very diferent from what I am use to seeing.
Posted By: Tegpilot
Date Posted: July 12, 2005 at 5:53 PM
Thanks, It's a Infinity Kappa 10" DVQ
Posted By: HottAccord
Date Posted: July 12, 2005 at 6:14 PM
Nice job, how does it sound and how thick did you go on the enclosure?
-------------
Im a fiberglass whore!!
Posted By: OCURIEL
Date Posted: July 13, 2005 at 6:51 PM
nice install. How does it sound?
Posted By: oxygen65
Date Posted: September 06, 2005 at 10:33 PM
looks really nice, almost a kind of factory look but you know that is isnt, i really like it
Posted By: Teamrf
Date Posted: September 07, 2005 at 6:51 PM
Good glassing job...
-------------
~The Rookie~
Rookie of the year that is...
Don't let the smoke out of your equiptment..it doesn't go back in.
Posted By: Tegpilot
Date Posted: September 07, 2005 at 9:55 PM
Thanks guys. It sounds great. To be honest I didn't really pay any attention to Infinity's specs for the enclosure. I was just trying to see if I could pull it off. It was my first time. But I tood it in and they said I performed exactly like it should according to there meter or whatever. I think it could use a little bit more power though, but it's very tight and clean. Poormanq, I really didn't cut but about 1/4 inch off to get a straight line, it kinda is a visual illusion. I could however have made the ring sit in closer and not stick out so far, but I would have lost volume, and at the very least I knew I didn't want to do that.
Posted By: asleepindc
Date Posted: October 19, 2005 at 9:16 PM
tegpilot, looks really good, but how did you manage to hold the fiberglass up??.. did you mount it to the panels or what did you do?? I'm thinking of doing something similar to my Teg and some help would be awesome!
Posted By: Tegpilot
Date Posted: October 21, 2005 at 7:35 PM
Asleep, thanks man. sorry i took so long to reply. Hey, I just pulled the trunk liner out as you can see and molding the enclosure. I drilled a hole thru the back of the enclosure and thru the trunk liner and put a small bolt thru. I used sone 1 inch plastic washers on the inside and back side to give some grabbing power to the bolt. That's it man. simple. Let me know if you need more help, or send pics when you get it done.
-------------
99 INTEGRA LS 4DR Forest Green.Alpine CDA9857 Deck. JBL 755.6 AMP, Kappa 50.7cs Front, Kappa 6x9's Rear, 4 JBL GTO804 subs
|