2006 tacoma bypass not programing
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=100951
Printed Date: May 04, 2024 at 5:42 AM
Topic: 2006 tacoma bypass not programing
Posted By: brianh
Subject: 2006 tacoma bypass not programing
Date Posted: January 08, 2008 at 9:17 PM
I have installed a remote start on my truck. It works great, but I am having trouble getting the bypass to program. The bypass I have is the xko5-pkt2 made by Peripheral. I have the chassis ground, 12 volts,imi, imo, and the (- out when running) all hooked up. I am also pretty sure I have the right data wires for the truck because the truck will crank but not start with the wire cut that I have hooked to the bypass. I am sorta stumped by this. If anyone has any info on this I would sure appreciate it. Thanks in advance. Brian
Replies:
Posted By: Velocity Motors
Date Posted: January 09, 2008 at 10:34 PM
Everytime you relearn the module you have to reset it. To RESET, press and hold button and plug in module. LED comes on. When LED goes off, release button.
Also, TACOMA V6: Wiring can be found in position 15 and 16 (PIN 15 instead of PIN 26 and PIN 16 instead of PIN 27). This connector is located behind glove compartment at ECM.
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: chriswallace187
Date Posted: January 10, 2008 at 7:29 AM
All that Jeff said, plus you didn't mention the blue ignition input wire from the XK05 being connected? ------------- C Renner's Auto Electronix
My service is cheap, quick, and good - pick any two
Posted By: brianh
Date Posted: January 10, 2008 at 5:12 PM
Thanks for the replys. I am not getting the red led to light up during pogramming. I do not have the blue ign. wire hooked up. The instructions didnt show it hooking up. That very well could be my problem. I quess it would be a good idea to hook up the green(-) oem security light turn off wire also. Thanks for the info guys. If someone could just let me know about that ign wire I will be set. Thanks a again. Brian
Posted By: moonliter
Date Posted: January 10, 2008 at 5:35 PM
The ignition wire is mandatory, it needs to be connected.
Posted By: brianh
Date Posted: January 10, 2008 at 7:09 PM
Even with the 12 volt constant wire? Not doughting what you are saying, I have just never seen a bypass that had two 12 volt inputs on the unit. Brian
Posted By: techman93
Date Posted: January 10, 2008 at 8:36 PM
That would be how it senses when key is turned on to program unit on some bypasses. The XK05 is what we use at our shop and I have done a few Toyota's that require to run bypass to behind glove box. You might have the IMI wires reversed. Violet and violet/white may need to be swapped. Test and reset before trying to reprogram.
The security light green wire should be hooked up and the blue wire to ignition as well.
Did the remote starter get tach programmed or is it on voltage sense? Check that and make sure it is set up correctly.
-------------
The wire I'm test'n isn't doin' what it's supposed to be doin'... I am so glad I printed that tech sheet, with the wrong info.
Do it right the first time... or I might have to fix it for ya
Posted By: brianh
Date Posted: January 11, 2008 at 4:28 PM
Thanks for the info. I will hook that blue ign. wire up tommorrow. (I did have to run the wires to the ecm behind the glove box.) I will let you know how it goes. Brian
Posted By: brianh
Date Posted: January 12, 2008 at 3:41 PM
Thanks for the info guys. Just hooked up the blue ignition wire and it programmed up the first time. The directions given with the bypass do not show hooking that wire up(for the Tacoma) Thanks again. Brian
Posted By: extreme1
Date Posted: January 12, 2008 at 8:04 PM
brianh wrote:
Thanks for the info guys. Just hooked up the blue ignition wire and it programmed up the first time. The directions given with the bypass do not show hooking that wire up(for the Tacoma) Thanks again. Brian
you have to hook it up no matter what vehicle it is. ------------- Shaughn Murley
Install Manager, Dealer Services
Visions Electronics
Red Deer, Alberta
|