xk01 amdl programming
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=101394
Printed Date: May 19, 2024 at 12:01 PM
Topic: xk01 amdl programming
Posted By: baypoint
Subject: xk01 amdl programming
Date Posted: January 20, 2008 at 1:21 PM
I am having trouble programming XK01, the led lights, I turn the key to on but the led won't flash it just stays on steady. Any suggestions?
Replies:
Posted By: chadwa2003
Date Posted: January 20, 2008 at 3:15 PM
What kind of vehicle is it? Did you hook up the ignition input?
Posted By: GregK
Date Posted: January 20, 2008 at 3:45 PM
Is it connected D2D or W2W?
Did you connect to the correct ODBII wire?
More details would be great, year, make and mpodel of vehicle and the RS unit you're hooking up.
-------------
GDK Electronics
Home theatre & mobile electronics installations
Winnipeg, MB
Posted By: baypoint
Date Posted: January 20, 2008 at 4:06 PM
05 Jeep Liberty Audiovox APS997 w2w Brown to RS ground when running Green to RS red lock Blue to RS green unlock violet/white to RS brown door trigger violet to ODBII pin 2 w/violet pink/white n/c pink n/c orange to RS dk blue trunk red to 12v black to ground
Posted By: GregK
Date Posted: January 20, 2008 at 4:56 PM
Did you manage to get the module programmed to type 7 for your Jeep first?
If so, turn the ignition on, the LED will remain lit, start the vehicle with the key and you should see the LED flash green.
If it does, it's now programmed.
If that doesn't work try resetting the module.
Unplug the 10 pin harness, hold the programming button in and plug the harness back in. Release the button when the LED flashes.
Program the unit to type 7 for your Jeep.
Start the vehicle with the key
You shouldn't have to change any mode options for your vehicle.
-------------
GDK Electronics
Home theatre & mobile electronics installations
Winnipeg, MB
Posted By: baypoint
Date Posted: January 20, 2008 at 5:56 PM
I tried starting and the LED stayed red, also tried to reset but when I hold the button in the LED never flashes. Maybe bad module?
Posted By: GregK
Date Posted: January 20, 2008 at 6:03 PM
Maybe it is a bad module. Which firmware is on it? Make sure it's AMDL 6.00
-------------
GDK Electronics
Home theatre & mobile electronics installations
Winnipeg, MB
Posted By: baypoint
Date Posted: January 20, 2008 at 6:08 PM
AMDL 6.0
Posted By: GregK
Date Posted: January 20, 2008 at 6:26 PM
I would say bad module if you're 100% sure all of your wiring connections are good.
-------------
GDK Electronics
Home theatre & mobile electronics installations
Winnipeg, MB
Posted By: robertsc
Date Posted: January 20, 2008 at 8:18 PM
GregK] wrote:
id you manage to get the module programmed to type 7 for your Jeep first?
If so, turn the ignition on, the LED will remain lit, start the vehicle with the key and you should see the LED flash green.
I.
i think your thinking of an idatalink module i have only seen red led's on bypasskits modules
Posted By: GregK
Date Posted: January 20, 2008 at 8:52 PM
I have no idea why I typed green. LOL. You're correct, it's red all the way through.
-------------
GDK Electronics
Home theatre & mobile electronics installations
Winnipeg, MB
|