i am installing a cx-4000 in a manual trans cobalt i have a idatalink solo module. what wire from the compustar brain do i hook up to the clutch to bypass it for remote start?? also on the idatalink ads-dlsl bypass i don't quite understand the green wire and purple / YELLOW wire notes....1st question is where do i hook green wire to the bcm or the cx-4000? 2nd is will that take care of both the door output status and RAP or is it on or the other??? will i need to connect the cx-4000 door status wire also ??? thanks!!
yellowcobaltlt wrote:
i am installing a cx-4000 in a manual trans cobalt i have a idatalink solo module. what wire from the compustar brain do i hook up to the clutch to bypass it for remote start??
You will need to hook up a relay to be triggered from the RED / BLACK 2nd STARTER (-) wire from the CN2 harness.
yellowcobaltlt wrote:
also on the idatalink ads-dlsl bypass i don't quite understand the green wire and purple / YELLOW wire notes....1st question is where do i hook green wire to the bcm or the cx-4000?
The green wire has 2 functionalities:
1- A door status (-) output (not required in 2-way
iDatalink mode.
2 - A rap shutdown (-) output, with the
PURPLE / black wire connected to ground. The green
wire must be connected to the driver door switch
to turn off radio at the end of the remote start
sequence.
The PURPLE / YELLOW wire goes to the BCM PIN #11 DARK GREEN
yellowcobaltlt wrote:
2nd is will that take care of both the door output status and RAP or is it on or the other???
It's either or, but not both. You must choose one or the other.
yellowcobaltlt wrote:
will i need to connect the cx-4000 door status wire also ??? thanks!!
Yes, this will shut the vehicle off when you get the vehicle into ready mode.
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
ok i need this a little clearer, if possible...1. can't i do it without a relay and just power the clutch directly? either way could direct me on exactly how to wire.. 2. next what exactly do i do with the green wire for the idatalink? do i hook it to a bcm wire for the rap? and ground the PURPLE / black??? and then would i need to connect the CM-4000 door output to the same bcm wire as the green from the idatalink module...am i correct?? they both need to see the door status?? thanks for your help!!
yellowcobaltlt wrote:
ok i need this a little clearer, if possible...1. can't i do it without a relay and just power the clutch directly? either way could direct me on exactly how to wire..
You should have a (+) trigger clutch wire that is YELLOW. Wire a relay like this:
85 - 2nd STARTER wire from CN2 Harness
86 - YELLOW starter wire from CN1 harness
87 - Goes to pin 86
30 - To YELLOW wire at clutch
87a - NOT USED
yellowcobaltlt wrote:
2. next what exactly do i do with the green wire for the idatalink? do i hook it to a bcm wire for the rap? and ground the PURPLE / black???
Read the answer above. If you want to use the iDatalink to do RAP shut down GROUND the PURPLE / BLACK wire. The green wire must be connected to the driver door switch to turn off radio at the end of the remote start sequence. The GREEN wire will do either the RAP shut down or output a (-) Door trigger. So if you want the RAP shut down option from the iDatalink, you will need to do as stated above. If you want to use the GREEN wire for door status instead, just wire up this wire to the RED / WHITE wire at the CN2 harness.
yellowcobaltlt wrote:
and then would i need to connect the CM-4000 door output to the same bcm wire as the green from the idatalink module...am i correct?? they both need to see the door status?? thanks for your help!!
Read above answer.
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
ok cool im getting there!! do i need diodes when hooking up the green for RAP? and/or diodes for the door trigger wire from the cm-4000? thanks
Hi guys i have a 07 cobalt and a compustart pro 2way starter/alarm. I was wondering if i could p/u a connection at the bcm for the rear defroster? if so where and what color? and what wire would i use from the compustar? the accessory? thanks in advace..