remote start 2008 chryslers w/new key
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=103168
Printed Date: May 02, 2024 at 9:48 PM
Topic: remote start 2008 chryslers w/new key
Posted By: skee-weezy
Subject: remote start 2008 chryslers w/new key
Date Posted: March 18, 2008 at 10:36 AM
alrite everyone... this is my first post.. so i wanna make it a good one..... i work in the field.. so serious replies only... i can easily separate bs from real talk.... is there anyone out there doing remote starters on the new chryslers and dodges w/ the new key... if so... what part are u using or how are u bypassing the new key????????? thanks in advance... ------------- there can be only one.......
Replies:
Posted By: tonyberg
Date Posted: March 18, 2008 at 11:00 AM
Idatalink ADS-AL-CA (multi series) only way to go I work for a large Dodge/Chrysler/Toyota dealer and its the ONLY module we stock
Posted By: skee-weezy
Date Posted: March 18, 2008 at 11:04 AM
hmmmm.. u know what... try telling that to my owner.... we are a compustar dealer and he still refuses to order them... go figure... can u give me some install details?????
-------------
there can be only one.......
Posted By: tonyberg
Date Posted: March 18, 2008 at 1:01 PM
Install on them is pretty simple as long as you are comfortable soldering to a circuit board. Id recommend a nice pencil style soldering station as you wont be able to use a trigger style "gun" soldering on on that circuit board. The idatalink modules take care of all the necessary commands inside the WIN (wireless igntion node) and also does door locks/power rear liftgate. They do NOT do power sliders yet, but when I called technical they said that was coming in the very near future. It takes care of the resistance for the MUX parking light circuit and also picks up brake over the bus.
Posted By: skee-weezy
Date Posted: March 18, 2008 at 1:13 PM
does it also work for the grand cherokee, charger, and 300c???????
-------------
there can be only one.......
Posted By: tonyberg
Date Posted: March 18, 2008 at 4:49 PM
yes....all vehicles equipped with the FOBIK style key
Posted By: Mike M2
Date Posted: March 19, 2008 at 6:55 AM
Ok, what is different with the 08 Chrysler key? We have been using 556cw's on Chrysler stuff, will it still work?
-------------
Mike M2
Tech Manager
CS Dealer Services
Posted By: tonyberg
Date Posted: March 19, 2008 at 7:32 AM
the 556cw will work for the actual transponder bypass, but the door locks, trunk, etc are fully bussed without a module there is virtually no way to control them (you could run wires to all the doors and 5 wire the door locks but this wouldnt control the alarm)
Posted By: skee-weezy
Date Posted: March 19, 2008 at 7:53 AM
alrite... so lemme get this straight... u are telling me that the universal transponder bypasses will still work... but only bypass the key... and that an installer would have to wire up and intricate series of relays diodes and all kinds of other doodie to do the job of this one piece.... alrite... sounds like me and my owner gotta have a talk.... i am tired of telling these customers to wait.. if there is a part already out there... we need to stock it... thanks a million man......
-------------
there can be only one.......
Posted By: vitrox
Date Posted: March 19, 2008 at 12:28 PM
you can also use the xk modules from bypasskit
Posted By: dtk1
Date Posted: April 20, 2008 at 9:58 PM
xk (<) idatalink this car are not your typical rs cars. this cars are basically run tru a data not having the right knowledge can cause you hole in your pocket i've done it both ways and trust me idatalink will save you time xk01 in the other hand is good however if you go with and xk 01 takes more time in the install and more wires to run.
|