Print Page | Close Window

2003 chevy venture

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=10583
Printed Date: October 31, 2024 at 6:26 PM


Topic: 2003 chevy venture

Posted By: alfred
Subject: 2003 chevy venture
Date Posted: March 08, 2003 at 10:00 AM

wiring colors for remote start



-------------
alfs



Replies:

Posted By: alfred
Date Posted: March 08, 2003 at 10:15 AM
how toi install audivox aa-rs5cs  also wiring harness colors

-------------
alfs




Posted By: Velocity Motors
Date Posted: March 08, 2003 at 11:02 AM

|       ITEM      |     WIRE COLOR     |POL|       WIRE LOCATION        |
|              12V|red & RED / white     |+  |ignition harness            |
|          STARTER|yellow              |+  |ignition harness            |
|         IGNITION|pink                |+  |ignition harness            |
|  SECOND IGNITION|white               |+  |ignition harness            |
|        ACCESSORY|orange              |+  |ignition harness            |
|       POWER LOCK|RED / black *3        |-  |BCM, to right of glove box  |
|     POWER UNLOCK|ORANGE / black *3     |-  |BCM, to right of glove box  |
|       LOCK MOTOR|gray                |   |BCM, to right of glove box  |
|     UNLOCK MOTOR|tan                 |   |BCM, to right of glove box  |
|    DISARM DEFEAT|tan                 |   |BCM, to right of glove box  |
| PARKING LIGHTS +|brown               |   |drivers kick or light switch|
| PARKING LIGHTS -|BROWN / white         |   |BCM, to right of glove box  |
|       HEADLIGHTS|yellow              |+  |headlight switch            |
|     DOOR TRIGGER|gray/black *1       |-  |BCM, to right of glove box  |
| DOME SUPERVISION|use door trigger    |   |                            |
|  TRUNK/HATCH PIN|tied in with doors  |   |                            |
|TRNK/HTCH RELEASE|*6                  |-  |*6                          |
|  FCTRY ALARM ARM|arms with lock      |   |                            |
|FCTRY ALRM DISARM|disarms with unlock |   |                            |
| DISARM NO UNLOCK|*4                  |   |                            |
|       TACHOMETER|PURPLE / white        |   |ign coils or PCM *5         |
|      SPEED SENSE|green               |   |BCM, to right of glove box  |
|       BRAKE WIRE|white               |+  |brake switch                |
|     HORN TRIGGER|black               |-  |BCM, to right of glove box  |
|           WIPERS|purple *2           |+  |wiper motor                 |
|  LF WINDOW UP/DN|blue - brown        |A  |drivers window switch       |
|  RF WINDOW UP/DN|lt. blu - tan       |A  |drivers door harness        |
|  LR WINDOW UP/DN|not recommended     |   |                            |
|  RR WINDOW UP/DN|not recommended     |   |                            |
|        RADIO 12V|orange              |   |radio                       |
|     RADIO GROUND|BLACK/ white         |   |radio                       |
|     RADIO SWITCH|yellow              |   |radio                       |
| RADIO ILLUMINATE|gray/black          |   |radio                       |
|       LF SPEAKER|tan - gray          |   |radio                       |
|       RF SPEAKER|lt. grn - green     |   |radio                       |
|       LR SPEAKER|brown - yellow      |   |radio                       |
|       RR SPEAKER|blue - lt. blu      |   |radio                       |

Notes:
NOTE: This vehicle is equipped with the pass-key III immobilizer. Use DEI part number 555G or 555U to bypass during remote start mode. Use the lt. green (-) key sense wire at the steering column to interrupt the blue wire on the 555U so that when the key is inserted to do take over the vehicle does not see two transponders at the same time. Refer to directfax document #1079 for wiring information.  *1 To avoid the domelight delay use tan for the drivers door, blue for the passenger door and the liftgate, and orange for the sliding doors. All wires are negative trigger, located at the BCM and all need to be diode isolated from each other.    *2 This wire is only activated when the wipers are in the high/fast position. There is not a wire for the low setting.  *3 The door lock wires will only meter when turning the key in either door key cylinder. Also have to program the door lock pulse duration for 3.5 seconds to unlock the doors. On vehicles without the factory alarm, use lt. blue for lock and white for unlock. Find the wires in either kick panel.  *4 To disarm the factory alarm without unlocking the doors, use a 0.8 second pulse on the unlock wire.  *5 The ignition coil pack is on the top of the engine on the passenger side. The PCM is in the air cleaner assembly on the front of the engine compartment on the driver side, the wire is in the blue plug in pin 8.  *6 The driver side power sliding door is lt. blue/black (-) in the driver kick panel in the harness going to the rear. The passenger side power sliding door is lt. blue (-) in the passenger kick panel in the harness going to the rear.



-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA




Posted By: alfred
Date Posted: March 08, 2003 at 4:02 PM

where can i hook in to so my remote start can sense the tach of the car.please let me know what color it is and where to find it exact location.



-------------
alfs




Posted By: floaterr
Date Posted: March 08, 2003 at 4:10 PM

It's right on the sheet that they already posted for you


TACHOMETER|PURPLE / white        |   |ign coils or PCM *5        |
*5 The ignition coil pack is on the top of the engine on the passenger side. --OR-- The PCM is in the air cleaner assembly on the front of the engine compartment on the driver side, the wire is in the blue plug in pin 8.


Good Luck




Posted By: alfred
Date Posted: March 08, 2003 at 7:21 PM
i have posted this question and recieved an answer thankyou very much. but i still can not find the tach wire to connect to i was told to look on the top left of engine and still could not find tach wire is this info wright please give more detail thanks again

-------------
alfs




Posted By: floaterr
Date Posted: March 08, 2003 at 7:30 PM

Are the wire colors not matching (the chart) or can you not find the ignition coil, nothing in the air filter box?

Aslo, select "post reply" not "new topic" here instead of starting a new thread. Don't want them to ban you before you've finished the project :)




Posted By: alfred
Date Posted: March 08, 2003 at 7:44 PM
ican not find the ignition coil on engine

-------------
alfs




Posted By: alfred
Date Posted: March 08, 2003 at 8:06 PM
when i install the module under the dash should i instal a relay between the ignition switch and the key module

-------------
alfs




Posted By: alfred
Date Posted: March 08, 2003 at 8:56 PM
thanks for your reply jeff there is a direct fax they talk about in your directions how to wire module 555u please send or reply

-------------
alfs




Posted By: camino
Date Posted: March 09, 2003 at 2:07 AM
yes he is rigth and i think is better to dollow his words
if you need the complete paper work let us know




Posted By: alfred
Date Posted: March 09, 2003 at 9:40 AM
 i have an audiovox remote start i have installed it in a 2003 venture the remote start will only work when the key is turned slighty foward not to the run position but just till you see the p on the shifter light then it will work fine.

-------------
alfs




Posted By: jrilla
Date Posted: March 09, 2003 at 3:37 PM
You need to get your bypass module installed.

I have a 2001 Venture and I did not use a keysense wire to shutoff the bypass module and everything is fine. I used the PKG5 though.



-------------
J Rilla

Owner/Installer




Posted By: Velocity Motors
Date Posted: March 09, 2003 at 4:28 PM
Hey Alfs, email me your email addy & I'll send you all the necessary files for the install if you haven't already got them from another member.

-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA




Posted By: alfred
Date Posted: March 09, 2003 at 6:15 PM
couple of things should i install a relay between the key module and ignition switch if so how to wire. the other problem is the remote start will only work when i turn the key up just enough to turn on the p on the shifter i dont have to go all the way to the run position is there another wire a third ignition wire i should look for i have not hooked the key module in yet but do leave the key in the ignition when i try to use the remote start

-------------
alfs




Posted By: jrilla
Date Posted: March 09, 2003 at 6:39 PM
I assume that you did not install ther bypass yet but please correct me if you have.

Just install the bypass without a relay and get back to us.

I assume that you have to turn the key a little so that the car tries to read the if there is a key in the ignition. That is a little wierd though because most vehicles you only need to insert it into the cylinder and not turn it at all.

-------------
J Rilla

Owner/Installer




Posted By: alfred
Date Posted: March 11, 2003 at 4:12 PM
i installed the key bypass and the remote start will still not work unless the key is turned just a little bit not all the way to run just a litte bit there must be another ignition wire all acc. turn on sounds like fuel pump engages but the shifter letters never light up which is what happens when i turn the key a little bit and the remote start works

-------------
alfs




Posted By: jrilla
Date Posted: March 11, 2003 at 4:14 PM
what wires do you have powered in the ignition harness?

-------------
J Rilla

Owner/Installer




Posted By: alfred
Date Posted: March 11, 2003 at 4:26 PM
i have  the red w/white treacer to to red wire incar red wire to red red wire yellow wire to yellow wire blue wire ign 1 tothe pink in car green wire to the white in the car violet wire to the orange wire in the car

-------------
alfs




Posted By: alfred
Date Posted: March 11, 2003 at 5:11 PM
ther is one xtra wire in the harness it looks to be black it has power in the run, acc but not in the start position

-------------
alfs




Posted By: ole3k
Date Posted: March 11, 2003 at 5:52 PM
I have the same remote starter,can i put trunk release on that

-------------
ole




Posted By: alfred
Date Posted: March 11, 2003 at 6:34 PM
no one can help are there any new wiring for the 2003 please hep

-------------
alfs




Posted By: alfred
Date Posted: March 12, 2003 at 5:42 PM
is there no installer out there that can help me i called audiovox and went through the whole wiring process with him he said it is possiable at start up there is a negative pulse sent out  has anyone else had a problem please let meknow i need some kind of help the company who made the thing had no answers

-------------
alfs




Posted By: Velocity Motors
Date Posted: March 12, 2003 at 5:57 PM

Hey Alfred, I went through all the posts and for you get get this starter going you have to answer these questiosn with as much detail as you can:

  • What brand & version number bypass module did you use to bypass the Passkey III System of the Venture ?
  • What wire did you use to power the bypass module from the remote starter ?


-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA




Posted By: alfred
Date Posted: March 12, 2003 at 6:03 PM
i used a model 555u iused one of trhe wires coming out of the ignition but with the key in and the module not installed it still did not work unless youy turned the key a little bit

-------------
alfs




Posted By: alfred
Date Posted: March 12, 2003 at 6:07 PM
brand was component

-------------
alfs




Posted By: Velocity Motors
Date Posted: March 12, 2003 at 6:18 PM

You have to have the 555U completely installed witht he GROUND OUT WHEN RUNNING wire hooked up as well as the other wires necessary for the module to work. If you have the 555U partially hooked up and the key not seated properly in the module, then it will not work at all.



-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA




Posted By: alfred
Date Posted: March 12, 2003 at 6:22 PM
the  bypas module is hooked up  and is hooked to the grond pulse wire of the remote start but even if this wasnt hooked up shouldnt the car see the key in the ignition and run the car will not crank at all

-------------
alfs




Posted By: Velocity Motors
Date Posted: March 12, 2003 at 7:41 PM
If the car does not crank at all it's probably an IGN or a STARTER wire connection error. Please list eh wires that you have from the Audiovox to the vehicle. I will compare what you have according to what you should have.

-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA




Posted By: alfred
Date Posted: March 13, 2003 at 6:28 PM
the wiring is red w/white tracer to red wire in car  red wire to red wire in car yellow wire to yellow wire in car blue wire to the pink wire in the car green wire to the white wire in the car violet wire to the orange wire in the car tach wire to white wire in harness

-------------
alfs




Posted By: alfred
Date Posted: March 15, 2003 at 7:20 AM
please help anyone thanks

-------------
alfs




Posted By: jrilla
Date Posted: March 15, 2003 at 7:47 AM
It sounds like you have an install issue. You may have a bad connection or a blown fuse on the RS. Test all of your vehicles ignition wires and accessory wires and starter wire to make sure they are all getting power at the proper time during a remote start attempt. Basically you need to test each wire by putting a test light on it and then press the start button and watch to see when the wire gets power. Take your time and look everything over.

I just thought about this; I dont remember anyone asking you what happens when you attempt to remote start the van when the key is out of the ignition. Does it do absolutely nothing? I mean the parking lights should come on, the fans should turn on, etc.

I have read your responses to the questions asked and I have to say it would be nice if you could try to respond in complete sentences and try to explain things in as much detail as possible. The more detail we have, the more easily we can help you. I am sure that your peoblem is just something small that you have overlooked.

-------------
J Rilla

Owner/Installer




Posted By: jrilla
Date Posted: March 15, 2003 at 7:53 AM
Alfred I forgot to ask you how you made your connections? Did you solder them?

-------------
J Rilla

Owner/Installer




Posted By: alfred
Date Posted: March 15, 2003 at 5:15 PM
i checked all the fuses they are all good. the lights flash and it sounds like afuel pump or somthing starts up when you try to remote start the car i have tryed switching ignition 1 and 2 the same thing happens lights flash .this all will happen with the key in  or out  but if i turn the key a little bit foward the car will start. i did solider all connections there are no cold solider joints.iwent threw all the wires each one gets power . ignitio 1 /2  and stater wire power up at start iwent as far as to run a wire off the yellow starter wire at the module to the starter motor it would crank it

-------------
alfs




Posted By: alfred
Date Posted: March 17, 2003 at 5:27 PM
the previos is areply to j rillas questions i went as far also today to return the module.i also found that the ignition 1 wire is the hot wire when i turn the key a little foward and the car starts. the new module did not help.

-------------
alfs




Posted By: alfred
Date Posted: March 17, 2003 at 7:14 PM

thank s for all your help it was a programing problem with the module you must turn off ignition 2during cranking or the car will not start another interesting point is the car will not remote start if you leave the key in the ignition but the the car will run fine after you turn the remote start off with both keys

                                                                posted_image  



-------------
alfs





Print Page | Close Window