Print Page | Close Window

security light on w/remote start

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=108081
Printed Date: May 13, 2025 at 10:24 PM


Topic: security light on w/remote start

Posted By: daveg6
Subject: security light on w/remote start
Date Posted: October 10, 2008 at 9:34 PM

I just had a prestige aps787 alarm/remote start put in my '07 pont g6.  It has the factory alarm, but not factory remote start (although I understand the capability is built in, just not activated).  I had initially thought to do the install myself, but it's been about 10 yrs since my last alarm install and I've never done a remote start install so I had local shop put it in.  They used  xk01 and xk06 bypass modules that I had bought and flashed with pkg7 firmware per the bypasskit website.

When I arm the new alarm the factory security light on the dash comes on, when I disarm it goes off.  When I remote start the car the gauges do their normal startup routine but then the security light comes on, quickly flashes off and then comes back on and stays on. 

I haven't noticed any issues with the vehicle running with the security light on, it's just annoying.  The guys at the shop said they would do research on it, but I wanted to do some checking myself but haven't found anything.  Anyone have any ideas?




Replies:

Posted By: reax222
Date Posted: October 11, 2008 at 9:39 AM
I assume your talking about the passive anti-theft light?

To do a remote start you have to bypass the PATS, with these CAN dashes, it's pretty nice because the module can do it without a lot of work plus they can give you other features with fewer wires. It's possible your interface/bypass informs the computer that the PATS is bypassed. However when you put your key in, the PATS light should go out. I'd check with your bypass company.




Posted By: daveg6
Date Posted: October 11, 2008 at 3:50 PM

OK, thanx for the advice.  Will check on bypasskits website





Posted By: KarTuneMan
Date Posted: October 11, 2008 at 8:50 PM

it's been about 10 yrs since my last alarm install and I've never done a remote start install so I had local shop put it in. 

Fixing this issue isn't really YOUR problem. Have your 'local shop" trouble shoot the install and fix it.



-------------




Posted By: howie ll
Date Posted: October 12, 2008 at 2:02 PM
Gary, look at my last post re 03 Mazda Miata I swear I wrote it before this post, told you we were twins........




Posted By: daveg6
Date Posted: October 12, 2008 at 4:02 PM

I'm all for giving the installers the opportunity to research the issue and by no means are they off the hook.  But to tell someone NOT to look for a solution...?   Hardly helpful.





Posted By: stevensnow01
Date Posted: October 29, 2008 at 8:49 PM
Did anyone find out the solution to this problem or is it perfectly okay?
I just installed a xk01 and PKUGM2X on a '07 G6. Does the same thing.




Posted By: daveg6
Date Posted: October 29, 2008 at 9:16 PM
Nope, haven't gotten an answer from anyone.  Tried the bypasskit.com's website but their form to send a question in isn't working and I haven't found a phone number to call them.  I've talked to a couple of other installers and they've said that it's a fairly common thing with pontiacs, no answer why tho.  Oh well, seems like we have to deal with an annoying light.




Posted By: blanx218
Date Posted: October 29, 2008 at 9:58 PM

heres a tech tip for your car. I had the same problem using the xk06. followed the instructions in  this document and you will be fine. no security light. 

https://www.directechs.com/tech_docs/Document10473-1130.pdf





Posted By: daveg6
Date Posted: October 30, 2008 at 8:36 AM
I have no access to directechs so I can't see that document.




Posted By: kgerry
Date Posted: October 30, 2008 at 12:38 PM
have you tried powering keysense?  that usually corrects the problem......

-------------
Kevin Gerry
Certified Electronics Technician
MECP First Class Installer

Owner/Installer
Classic Car Audio
since 1979





Print Page | Close Window