2000 chrysler cirrus data wire
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=108602
Printed Date: April 28, 2024 at 4:22 AM
Topic: 2000 chrysler cirrus data wire
Posted By: ashron02
Subject: 2000 chrysler cirrus data wire
Date Posted: November 01, 2008 at 8:38 PM
I've installed the new Autopage RS-1000 OLED in a 2000 Chrysler Cirrus. Everything went well until I was installing the XK531. All connections went well until I got to the Violet "Data" Wire on the XK531. The violet wire is supposed to get connected to pin 2 on the OBDII connector. The problem is this vehicle's pin 2 is blank. Is there an alternate data wire I can use to finish this install? The LED on the XK531 won't go out because there is no data. Any help would be greatly appreciated.
-------------
Another install, Another Dollar
Replies:
Posted By: jar754
Date Posted: November 02, 2008 at 1:44 AM
are you sure your reading the connector right,
Posted By: brhaugen
Date Posted: November 02, 2008 at 7:19 AM
I have never seen one without the data wire.
Pin 2 - reading left to right - WIDE side of the connector.
-------------
Brent Haugen
Fargo, ND
Posted By: ashron02
Date Posted: November 02, 2008 at 7:42 AM
Yes, I'm reading the connector right. I even unmounted it. Wide side up, left to right. Plus the pins are marked on the connector. Still nothing. I agree with you all, I too have never seen one without the data wire. I've done many Chrysler, Plymouth, and Dodge before, but never ran into an issue like this. Just for a sanity check I went to check my buddy's 2001 Plymouth Neon, and what did I find: A Pin2 data wire. I'm so confused. Here are the pins that are in the connector: 3, 4, 5, 6, 7, 11, 14, and 16. So, is there an alternate data wire?
-------------
Another install, Another Dollar
Posted By: jar754
Date Posted: November 02, 2008 at 9:42 PM
i'm thinking that they missplaced the wire into plug 3, but to verify look at your buddys connector and find the wire color on pin 2 and then look at yours,
Posted By: ashron02
Date Posted: November 03, 2008 at 11:30 AM
I tried Pin 3 and it won't make the XK531 led go out either. ------------- Another install, Another Dollar
Posted By: jar754
Date Posted: November 03, 2008 at 7:38 PM
once the carsprogrammed the led should be on ,insert key and turn to on position and led should go off, does it
Posted By: ashron02
Date Posted: November 03, 2008 at 11:44 PM
The LED won't go off, because the XK531 can't finish programming. There is no data connection, because pin 2 is missing, to finish the programming.
-------------
Another install, Another Dollar
Posted By: jar754
Date Posted: November 04, 2008 at 5:57 AM
try pin 7 most chryslers and some imports use this,pin 2 is used on most fords and some chryslers
Posted By: ashron02
Date Posted: November 04, 2008 at 5:59 PM
Pin 7 didn't work either. I just ended up using the XK531 just for transponder purposes. I ended up running external relays for the door locks, factory disarm, etc. Before I could say "I never ran across a vehicle that didn't have a data wire that was supposed to have one". Now I can. Even though there was an alternate way, I still hate the fact I wasn't able to utilize the ease of use the XK531 provides. Lesson learned: Check for data wire before starting install. Thank You ALL for all of your support.
-------------
Another install, Another Dollar
Posted By: jar754
Date Posted: November 04, 2008 at 11:16 PM
it has t ohave a data wire call the dealer and ask them also did you look at the color of your buddys pin2 wire color and then go back to yours and find that color and try.if it doesnt have a data wire then an obd2 reader cannot comunnicate with the ecm
|