I have a valet 562T remote start that i want to install on a 2004 pontiac aztek with keyless entry and GM's passkey III anti-theft security system. i looked up the wiring diagram for my car and it is listed like this:
INSALLATION WIRING GUIDE - Pontiac / Aztek / 2004 / All Info
Item Wire Color Pol Wire Location
12volts orange + Ignition harness
starter yellow + Ignition harness
second starter N/A
ignition pink+ Ignition harness
second ignition green + Ignition harness
3rd ignition N/A
accessory orange + Ignition harness
second acc brown + Ignition harness
keysense lt.green - Ignition harness
power lock RED / black - pink plug @ BCM
notes: lock requires a negative trigger thur a 470 ohm resistor. unlock requires a straight negative trigger. the BCM is located at the front of the center console under the radio.
power unlock same wire as power lock
lock motor gray 5wi back of fuse box.
black plug
unlock motor tan 5wi "
disarm defeat tan 5wi "
parking lights+ do not use
parking lights- lt.blue - headlights switch
headlightyellow - headlights switch
reverse light lt.green + back fusebox blk plug
door trigger blue/white -pink plug @ BCM
dome supervision use door trigger
trunk/hatch pin pink/black -pink plug @ BCM
trunk/hatch release WHITE/ black - 16pin grayplug@bcm
factory alarm disarm purple -pink plug @ BCM
tachometer purplr/white ac ignition coil
speed sense green 4K 16pingrayplug@bcm
brake wire white + brake pedal swtch
parking brake ORANGE / black -pink plug @ BCM
horn trigger black -steering column
wipers green(L),purple(H) +steering column
Immobilizer bypass required:Yes type: PASS-Key III
I hope this info helps some of you guys who had trouble finding the wiring info.
i have a few questions about this list.on the disarm defeat polarity column it says 5wi what does this mean? and on the wipers wire color column it says green(L),purple(H) what does the (L) and the (H) mean? thanks for the help i am not a newbie but i have never installed a remote start before, only car alarms and radios and amps.
-------------
get r done!!!!!!!
don't worry about the "disarm defeat", won't use it. IF you have a factory alarm you'll use the "factory alarm disarm". and why are you wanting to connect to the wipers? L= low H=high
hey i dont need to hook to the wipers but in the ignition harness there are like three green and two yellow wires so i needed to find out which one was the right wire its ok now i got the remote start working no problem, but now i need to know which wires to use to hook up a 555g imobilizer bypass.
the instructions list a color code but i dont think this is the right list, i need to know how to find the data in/out from the transponder unit at the key, and i need to basicaly get a list of the colors of the wires i need and where are they at. thanks
-------------
get r done!!!!!!!
cool i got the remote start working with no problems the only thing that i got left to do is to hook up the door locks the 2004 pontiac aztek has a 1 wire negative door trigger the wire color at the BCM is RED / black i have a ALA-DL1 programmable relay pack but i have no idea how to hook this thing up. if anyone knows how to get the lock/unlock funtion to work on a 2004 aztek with factory keyless entry i would be really grateful. thanks for the help in advance.
-------------
get r done!!!!!!!
yea i have the wire colors and location but i have never installed an alerm or remote system on a car with a single wire negative door trigger system. i dont know how to wire the relays and where to put the resistor at?if anyone knows how to get the lock unlock working on a azntek with factory keyless and a valet 562T remote start please help i tried hooking the green and blue wires (the lock unlock wires)on the 562T straight to the blue/white wire at the bcm and on the one i put the resistor on the wire and all it would do is make a sound like it was unlocking or locking but the lock swtich didnt move at all just the noise.so i am thinking i need to add some relays to the setup?
-------------
get r done!!!!!!!