clifford matrix 1 wiring
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=108976
Printed Date: May 15, 2024 at 11:19 AM
Topic: clifford matrix 1 wiring
Posted By: elton_23
Subject: clifford matrix 1 wiring
Date Posted: November 17, 2008 at 12:52 AM
i installed a clifford matrix 1 alarm .... and was wondering about the door trigger wires im pretty sure its a nagitive type so do i just hook up the green wire from the trigger wire to that ??? also what does the dome light supervision do ? can i just tap it into the light around the ignition as it comes on with the dome light
Replies:
Posted By: elton_23
Date Posted: November 17, 2008 at 12:53 AM
also im not sure about the shock sensor i have it turned up all the way and it takes a pretty hard hit to get it to chirp
Posted By: howie ll
Date Posted: November 17, 2008 at 10:50 AM
Door trigger wires are usually neg going so the green, what vehicle? What is your shock sensor mounted to?
Posted By: elton_23
Date Posted: November 17, 2008 at 1:20 PM
this is a 98 toyota 4runner as for the shock sensor its mounted on the tranny tunnel
Posted By: howie ll
Date Posted: November 17, 2008 at 2:50 PM
Green is ok, dome light supervision is simply bringing on the dome light for up to 1 min when you turn off the alarm. connect green to the switched side of the dome light, probably a RED / white wire with silver dots.
Posted By: howie ll
Date Posted: November 18, 2008 at 2:00 AM
Sorry forgot to add this.... mount the shock sensor with cable ties to a thick loom, experience teaches us that your location makes it too rigid, thus lack of sensitivity. quick and dirty fix, minimise the setting then increase it a fraction, bash the window frame front or rear or adjacent to the door keyholewith the flat of your hand.
Posted By: elton_23
Date Posted: November 18, 2008 at 4:22 PM
i do have it in a wire loom im thinking about ditching it and getting a proximity sensor
Posted By: elton_23
Date Posted: November 19, 2008 at 3:44 AM
do i have the sensor wired wrong ? it's just plug it in and put it some where since it didn't come with tape or anything or is the place i have it too solid ? ........ also i can set the alarm and shake the sensor and still get nothing
Posted By: howie ll
Date Posted: November 19, 2008 at 1:37 PM
I think the alarm has to be turned on before it's active, also make sure the white plug is pushed fully home.
Posted By: elton_23
Date Posted: November 20, 2008 at 12:16 AM
well i tried it again to day cranked it all they way up still nothing .... i can kick the tires jump on it slap the window .... but the funny thing is i come home and where i park about 60 feet theres train tracks these trains do maybe 10mph and come by once and awhile and they dam thing goes off
Posted By: elton_23
Date Posted: November 22, 2008 at 6:51 AM
any other ideas where to place the shock sensor ?
Posted By: elton_23
Date Posted: January 04, 2009 at 12:42 AM
got more questions i have a set of hella driving lights could i wire them up so i can push the trunk button and they will turn on ? and i was thinking about wiring the aux button to my air horn these all have relays soo do i just tap into the power wire from the switch inside ?
Posted By: elton_23
Date Posted: January 04, 2009 at 1:21 AM
also i notice the red light on the shock sensor is on when the alarm is off ?
|