2003 silverado, ungo rk1
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=109002
Printed Date: April 28, 2024 at 5:14 PM
Topic: 2003 silverado, ungo rk1
Posted By: Fosgate3
Subject: 2003 silverado, ungo rk1
Date Posted: November 17, 2008 at 8:32 PM
I've been searching through the forums and I find a number of questions about the GWR wire but I can't seem to find anything about the GWR and the Ungo RK1 so here goes.... I'm putting in an Ungo RK1 Keyless and Remote Start system in a 2003 Silverado this weekend. I'm using a DEI XK01 module to integrate into the BCM of the truck and I was curious about which wire the brown wire of the XK01 (GWR) would connect to on the RK1. Of the numerous wires, the few that make sense include: a blue (-) 200mA status output (located on the 7-pin "remote start ribbon harness" of the RK1); a blue/white (-) 200mA 2nd status/rear defogger - latched/pulse (on the 5-pin "remote start harness H3"); an orange (-) 500mA armed output (on the 12-pin "primary harness H1"), and another blue (-) 200mA status output (on the 4-pin "remote start auxiliary harness"). The rest of the options don't appear to be viable options; however, I've been wrong before!! LOL Thanks in advance for taking the time to read and/or reply!!!!
Replies:
Posted By: big sexy lac
Date Posted: November 17, 2008 at 10:55 PM
never did an ungo, but either one of the blue(-)status out puts will due. the wire should go to ground when the remote start engages so the brown wire on the xk01 sees ground.
-------------
WELL?
Posted By: Fosgate3
Date Posted: November 18, 2008 at 5:12 AM
Excellent. Thanks for the fast reply. I will be doing this RS system this saturday and I'll update the post then.
Posted By: Fosgate3
Date Posted: November 22, 2008 at 3:49 PM
I'm installing an Ungo RK1 keyless and remote start on a 2003 Silverado. I'm wondering where the wires that are used for the power lock/unlock. All the documents I seem to find on our forum point to a lt.blue wire and a white wire in the BCM. I found a lt.blue and a white wire in the brown BCM plug but they don't do anything when the lock/unlock button is pressed. Shouldn't there be a positive pulse? Thanks in advance. ------------- i think a wire's loose somewhere...
Posted By: another-kelly
Date Posted: November 22, 2008 at 6:37 PM
use the xk01 for locks on the '03-'07(classic) full size GM truck platforms
Posted By: Fosgate3
Date Posted: November 22, 2008 at 6:51 PM
Thanks. I think I misunderstood the nature of add-on modules. I was looking for a lock wire and an unlock wire. After looking at other posts here and elsewhere, I realized that you dont need those in this application--the XK01 will do it all on it's own, apparently through the vehicle's data wire. Technology is amazing...
-------------
i think a wire's loose somewhere...
Posted By: Fosgate3
Date Posted: November 22, 2008 at 7:29 PM
Everything works but now, the dome light will not come on when you open the doors. I never noticed if this was an issue before but it seems that the light should come on with the opening of the doors. It works fine for domelight supervision with the keyless... just not when you open the door. ------------- i think a wire's loose somewhere...
Posted By: another-kelly
Date Posted: November 23, 2008 at 8:43 AM
did you try turning off the domelight override pushbutton?
Posted By: Fosgate3
Date Posted: November 23, 2008 at 4:50 PM
No I didn't. Sorry to sound ignorant but I didn't know there was such a beast! I'll look around. Aside from that, the keyless/RS system works great!
-------------
i think a wire's loose somewhere...
Posted By: OmarR
Date Posted: November 23, 2008 at 6:00 PM
It's right next to the headlight switch.
|