viper 5701 and xk532 in 06 grand cherokee
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=109247
Printed Date: May 17, 2024 at 4:13 PM
Topic: viper 5701 and xk532 in 06 grand cherokee
Posted By: BrianM83
Subject: viper 5701 and xk532 in 06 grand cherokee
Date Posted: November 25, 2008 at 9:09 PM
I will be installing this setup into an 06 Jeep Grand Cherokee and have a few questions about the remote starter connections. I think I have it figured out, but if anyone has experience with this please let me know if you see something wrong.
[URL=https://www.the12volt.com/installbay/forum_posts.asp~TID~90188]https://www.the12volt.com/installbay/forum_posts.asp~TID~90188[/URL]
wires from Viper 5701:
Heavy gauge remote start, (H3) 10-pin connector
1 PINK (+) IGNITION 1 [tap into pink/lt. green]
2 RED / WHITE (30A) [not needed]
3 ORANGE ACCESSORY [not needed]
4 VIOLET (+) STARTER OUTPUT [car side of cut pink/orange, XK532 pink]
5 GREEN (+) STARTER INPUT [key side of cut pink/orange]
6 RED (+) [lt. blue/red]
7 PINK/WHITE (+) IGNITION 2 [not needed]
8 PINK/BLACK [not needed]
9 RED / BLACK [not needed]
10 N/C N/C
Remote start auxiliary output, 5-pin
4 PINK (-) 200mA IGNITION 1 OUTPUT [XK532 brown]
wires from XK532:
Brown Activation Input [5701 5-pin pink]
Violet/White MUX [tap into PURPLE / brown]
Pink Start Input [car side of cut pink/orange, 5701 violet]
Replies:
Posted By: a137
Date Posted: November 26, 2008 at 8:26 PM
Have done the same setup on JGC SRT8 06/
Wiring at https://www.the12volt.com/installbay/forum_posts.asp~TID~90188 is basically correct
You have to supply +12 and ground for XK mudule and make W2W connection to Viper
I've done D2D and have some problems with it (look at a few threads initiated by me)
Posted By: BrianM83
Date Posted: November 30, 2008 at 1:35 AM
I got everything connected as I listed above, but the remote starter is not starting. I can start it fine with the key and I am not getting any lights or problems. When I try starting with the remote starter, it will turn on, but not crank. I am not getting any voltage increase on the violet starter output. Its as if the remote start isn't trying to start. Any one have any ideas?? Thanks
Posted By: BrianM83
Date Posted: November 30, 2008 at 9:37 PM
I figured it out right after I made this post. Everything was right, i was just missing the RED / black wire.
Posted By: stiver_32
Date Posted: November 30, 2008 at 9:38 PM
I PM'ed you back. Do you have a link to the Viper 5701 install manual?? Do you have your MUX and data connections soldered?? this is a must!!! Any issues programming sentry key to the bypass ?? Does this bypass output the correct resistance values for Accessory and Starter #2 across the MUX without having to add resistors to the wire yourself ???
Posted By: stiver_32
Date Posted: November 30, 2008 at 9:41 PM
Good to hear. I run into the same issue alot.... alwayz seem to forget to hook up 1 wire.
|