viper 160xvl remote start wiring
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=110689
Printed Date: June 01, 2024 at 4:39 PM
Topic: viper 160xvl remote start wiring
Posted By: 94silverado
Subject: viper 160xvl remote start wiring
Date Posted: January 15, 2009 at 4:16 PM
i've installed a few remote starters so most of the wires are self explanatory. but there is a harness (remote start aux.) that plugs into the satellite relay. the diagram states they are for Status Input, Acc Relay Trigger, Starter Relay Trigger, Ign Relay Trigger. my question is this a mandatory harness? if it is, what circuits to they go to.
Replies:
Posted By: 94silverado
Date Posted: January 15, 2009 at 4:29 PM
forgot to add that this is for a 94 k1500 with no alarm system.
Posted By: kgerry
Date Posted: January 15, 2009 at 5:03 PM
these are used to trigger additional relays... you wont need it....
-------------
Kevin Gerry
Certified Electronics Technician
MECP First Class Installer
Owner/Installer
Classic Car Audio
since 1979
Posted By: 94silverado
Date Posted: January 16, 2009 at 10:54 PM
thats what i thought but wanted to make sure. the problem is i have everything wired up that i need but its not working properly. when i press the lock and unlock buttons the lights flash accordingly and the led shows it arming and disarming. but the locks arent actually working. when i try to remote start it doesnt do anything. have good ground and every wire i tapped into is correct and sending proper signal.
Posted By: robertsc
Date Posted: January 17, 2009 at 7:45 AM
vehicle no start is usually nutral safety wire,hood pin or brake wire
Posted By: advanced
Date Posted: January 17, 2009 at 9:44 AM
How did you hook up to door locks? What wires did you use in car?
-------------
Good Enough Isn't!
Posted By: 94silverado
Date Posted: January 17, 2009 at 10:01 AM
in the drivers kick panel is the wiring harness for the door. i believe the light blue and BLACK/ with red are the wires for the door locks. both have signals when you lock or unlock. i taped into those.
Posted By: advanced
Date Posted: January 17, 2009 at 10:07 AM
Is it a 2-door or 4-door? Are the door lock wires thin or thick? A 2-door is type C door locks & will require relays. ------------- Good Enough Isn't!
Posted By: 94silverado
Date Posted: January 17, 2009 at 10:36 AM
yes it is a two door. so both lock and unlock will require relays?
Posted By: advanced
Date Posted: January 17, 2009 at 11:26 AM
Yes, you'll need 2 relays on those 2 wires. I will find a diagram on this site & post it here. ------------- Good Enough Isn't!
Posted By: advanced
Date Posted: January 17, 2009 at 11:28 AM
| 5 Wire Alternating 12 Volts Positive Door Locks | Like the configuration above, the switch, when moved in either direction, applies both power and ground directly to motor legs without the use of any relays. Except, at the switch in this case, both motor legs rest at ground . Therefore it is only necessary to change the polarity of one motor leg to lock or unlock the vehicle.
 |
------------- Good Enough Isn't!
Posted By: 94silverado
Date Posted: January 17, 2009 at 9:19 PM
just wanted thank those who gave their advise. it made this install go easy. you guys know what you are doing.
great forum
|